Busybox dies on booting

Zachár Balázs bzachar at direkt-kfki.hu
Fri Mar 20 12:20:31 UTC 2009


Post inittab file

Roger Varley wrote:
> 2009/3/20 Zachár Balázs <bzachar at direkt-kfki.hu>:
>> Arch?
>> Post the console log here...
>>
> Architecture is X86 (the board is from Vortex using their A9100 CPU)
> The console log follows;
> 
>   Booting '2.6.28.8-1.nomodules - Serial Port'
> 
> root (hd0,0)
>  Filesystem type is ext2fs, partition type 0x83
> kernel /boot/vmlinuz-2.6.28.8-1.nomodules console=ttyS0,115200 ip=192.168.0.64:
> 192.168.0.65:192.168.0.65:255.255.255.0:babylon5:eth0:off nfsroot=192.168.0.65:
> /home/roger/vortex root=/dev/nfs rw
>    [Linux-bzImage, setup=0x2a00, size=0x16c650]
> 
> BIOS EBDA/lowmem at: 0009dc00/0009dc00
> Linux version 2.6.28.8-roger (roger at babylon5) (gcc version 4.3.1
> 20080507 (prerelease) [gcc-4_3-branch revision 135036] (SUSE Linux) )
> #1 Wed Mar 18 17:45:36 EET 2009
> KERNEL supported cpus:
>   Intel GenuineIntel
>   AMD AuthenticAMD
>   NSC Geode by NSC
>   Cyrix CyrixInstead
>   Centaur CentaurHauls
>   Transmeta GenuineTMx86
>   Transmeta TransmetaCPU
>   UMC UMC UMC UMC
> BIOS-provided physical RAM map:
>  BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
>  BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
>  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
>  BIOS-e820: 0000000000100000 - 0000000008000000 (usable)
>  BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
> DMI not present or invalid.
> last_pfn = 0x8000 max_arch_pfn = 0x100000
> 128MB LOWMEM available.
>   mapped low ram: 0 - 08000000
>   low ram: 00000000 - 08000000
>   bootmap 00001000 - 00002000
> (6 early reservations) ==> bootmem [0000000000 - 0008000000]
>   #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
>   #1 [0000100000 - 00003f35dc]    TEXT DATA BSS ==> [0000100000 - 00003f35dc]
>   #2 [00003f4000 - 00003f7000]    INIT_PG_TABLE ==> [00003f4000 - 00003f7000]
>   #3 [000009dc00 - 0000100000]    BIOS reserved ==> [000009dc00 - 0000100000]
>   #4 [0000007000 - 0000025000]          PGTABLE ==> [0000007000 - 0000025000]
>   #5 [0000001000 - 0000002000]          BOOTMAP ==> [0000001000 - 0000002000]
> Zone PFN ranges:
>   DMA      0x00000000 -> 0x00001000
>   Normal   0x00001000 -> 0x00008000
> Movable zone start PFN for each node
> early_node_map[2] active PFN ranges
>     0: 0x00000000 -> 0x0000009d
>     0: 0x00000100 -> 0x00008000
> Allocating PCI resources starting at 10000000 (gap: 8000000:f7000000)
> Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32413
> Kernel command line: console=ttyS0,115200
> ip=192.168.0.64:192.168.0.65:192.168.0.65:255.255.255.0:babylon5:eth0:off
> nfsroot=192.168.0.65:/home/roger/vortex root=/dev/nfs rw
> Initializing CPU#0
> PID hash table entries: 512 (order: 9, 2048 bytes)
> Console: colour VGA+ 80x25
> console [ttyS0] enabled
> Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
> Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
> Memory: 126236k/131072k available (2028k kernel code, 4288k reserved,
> 662k data, 208k init, 0k highmem)
> virtual kernel memory layout:
>     fixmap  : 0xfffed000 - 0xfffff000   (  72 kB)
>     vmalloc : 0xc8800000 - 0xfffeb000   ( 887 MB)
>     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
>       .init : 0xc03a4000 - 0xc03d8000   ( 208 kB)
>       .data : 0xc02fb363 - 0xc03a0e20   ( 662 kB)
>       .text : 0xc0100000 - 0xc02fb363   (2028 kB)
> Checking if this processor honours the WP bit even in supervisor mode...Ok.
> SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
> Calibrating delay loop... 99.32 BogoMIPS (lpj=496640)
> Mount-cache hash table entries: 512
> CPU: Cyrix Cx486SLC
> Checking 'hlt' instruction... OK.
> Freeing SMP alternatives: 0k freed
> net_namespace: 288 bytes
> NET: Registered protocol family 16
> PCI: Using configuration type 1 for base access
> SCSI subsystem initialized
> usbcore: registered new interface driver usbfs
> usbcore: registered new interface driver hub
> usbcore: registered new device driver usb
> PCI: Probing PCI hardware
> pci 0000:00:07.0: default IRQ router [17f3:6031]
> bus: 00 index 0 io port: [0x00-0xffff]
> bus: 00 index 1 mmio: [0x000000-0xffffffff]
> NET: Registered protocol family 2
> IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
> TCP established hash table entries: 4096 (order: 3, 32768 bytes)
> TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
> TCP: Hash tables configured (established 4096 bind 4096)
> TCP reno registered
> NET: Registered protocol family 1
> platform rtc_cmos: registered platform RTC device (no PNP device found)
> msgmni has been set to 246
> io scheduler noop registered
> io scheduler deadline registered (default)
> isapnp: Scanning for PnP cards...
> isapnp: No Plug & Play device found
> Real Time Clock Driver v1.12ac
> Serial: 8250/16550 driver4 ports, IRQ sharing enabled
> serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
> brd: module loaded
> loop: module loaded
> <6>r6040: RDC R6040 NAPI net driver,version 0.19 (18Dec2008)
> 
> Uniform Multi-Platform E-IDE driver
> it821x 0000:00:0c.0: IDE controller (0x17f3:0x1010 rev 0x11)
> it821x 0000:00:0c.0: controller in pass through mode
> it821x 0000:00:0c.0: 100% native mode on irq 10
>     ide0: BM-DMA at 0xed00-0xed07
>     ide1: BM-DMA at 0xed08-0xed0f
> ide0 at 0xef00-0xef07,0xee82 on irq 10
> ide1 at 0xee00-0xee07,0xed82 on irq 10
> ide_generic: please use "probe_mask=0x3f" module parameter for probing
> all legacy ISA IDE ports
> ide2 at 0x1f0-0x1f7,0x3f6 on irq 14
> ide3 at 0x170-0x177,0x376 on irq 15
> ide-gd driver 1.18
> Driver 'sd' needs updating - please use bus_type methods
> ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> ehci_hcd 0000:00:0a.1: EHCI Host Controller
> ehci_hcd 0000:00:0a.1: new USB bus registered, assigned bus number 1
> ehci_hcd 0000:00:0a.1: request interrupt 15 failed
> ehci_hcd 0000:00:0a.1: USB bus 1 deregistered
> ehci_hcd 0000:00:0a.1: init 0000:00:0a.1 fail, -16
> ehci_hcd: probe of 0000:00:0a.1 failed with error -16
> ehci_hcd 0000:00:0b.1: EHCI Host Controller
> ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 1
> ehci_hcd 0000:00:0b.1: irq 9, io mem 0x000de100
> ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 2 ports detected
> ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
> ohci_hcd 0000:00:0a.0: OHCI Host Controller
> ohci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 2
> ohci_hcd 0000:00:0a.0: request interrupt 14 failed
> ohci_hcd 0000:00:0a.0: USB bus 2 deregistered
> ohci_hcd 0000:00:0a.0: init 0000:00:0a.0 fail, -16
> ohci_hcd: probe of 0000:00:0a.0 failed with error -16
> ohci_hcd 0000:00:0b.0: OHCI Host Controller
> ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2
> ohci_hcd 0000:00:0b.0: irq 5, io mem 0x000dd000
> usb usb2: configuration #1 chosen from 1 choice
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 2 ports detected
> Initializing USB Mass Storage driver...
> usbcore: registered new interface driver usb-storage
> USB Mass Storage support registered.
> PNP: No PS/2 controller found. Probing ports directly.
> serio: i8042 KBD port at 0x60,0x64 irq 1
> serio: i8042 AUX port at 0x60,0x64 irq 12
> mice: PS/2 mouse device common for all mice
> TCP cubic registered
> NET: Registered protocol family 17
> RPC: Registered udp transport module.
> RPC: Registered tcp transport module.
> Using IPI Shortcut mode
> IP-Config: Complete:
>      device=eth0, addr=192.168.0.64, mask=255.255.255.0, gw=192.168.0.65,
>      host=babylon5, domain=, nis-domain=(none),
>      bootserver=192.168.0.65, rootserver=192.168.0.65, rootpath=
> Looking up port of RPC 100003/2 on 192.168.0.65
> Looking up port of RPC 100005/1 on 192.168.0.65
> VFS: Mounted root (nfs filesystem).
> Freeing unused kernel memory: 208k freed
> Kernel panic - not syncing: Attempted to kill init!


More information about the busybox mailing list