[Buildroot] [PATCH v3 4/4] configs/stm32mp157c-dk2: add support for wifi
Shlomi Vaknin
shlomi.39sd at gmail.com
Sat Oct 10 20:48:55 UTC 2020
Hi Bartek,
I did as you said and it didn't work. Here are the steps I did:
1. I changed as you said - didn't work.
2. I flashed the original image from st - works.
3. I flashed again the buildroot image - works.
4. I did hard reset - not working.
Can you verify that you have this experience?
בתאריך שבת, 10 באוק׳ 2020 ב-22:01 מאת Bartosz Bilas <
b.bilas at grinn-global.com>:
> Hi Shlomi,
> On 10.10.2020 17:41, Bartosz Bilas wrote:
>
> Hello Shlomi,
> On 09.10.2020 21:13, Shlomi Vaknin wrote:
>
> HI!
>
> According to u-boot I have the same revision as you. Could you try the
> formal version from st:
> https://www.st.com/en/embedded-software/stm32mp1starter.html ? I flashed
> it and the wifi worked. Just to be sure that there is no issue or something
> else with your board.
>
> Best
> Shlomi
>
> I've used:
>
> ST OpenSTLinux - Weston - (A Yocto Project Based Distro)
> 3.1-openstlinux-5.4-dunfell-mp1-20-06-24 stm32mp1 ttySTM0
>
> and everything seems to be ok
>
> root at stm32mp1:~# ifconfig -a
> eth0 Link encap:Ethernet HWaddr 00:80:E1:42:56:44
> UP BROADCAST MULTICAST MTU:1500 Metric:1
> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
> Interrupt:48 Base address:0x4000
>
> lo Link encap:Local Loopback
> inet addr:127.0.0.1 Mask:255.0.0.0
> inet6 addr: ::1/128 Scope:Host
> UP LOOPBACK RUNNING MTU:65536 Metric:1
> RX packets:80 errors:0 dropped:0 overruns:0 frame:0
> TX packets:80 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:6080 (5.9 KiB) TX bytes:6080 (5.9 KiB)
>
> usb0 Link encap:Ethernet HWaddr 4E:12:37:C3:7B:6C
> UP BROADCAST MULTICAST MTU:1500 Metric:1
> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>
> wlan0 Link encap:Ethernet HWaddr 10:98:C3:5F:FB:F9
> BROADCAST MULTICAST MTU:1500 Metric:1
> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>
> I'm gonna double-check one more time what's wrong with buildroot's image
> though.
> Best
> Bartek
>
> I've got this working fine, I had to add
> BR2_PACKAGE_MURATA_CYW_FW_CYW43430 instead of
> BR2_PACKAGE_LINUX_FIRMWARE_BRCM_BCM43XXX as I mentioned before, I also
> added BR2_PACKAGE_WPA_SUPPLICANT_PASSPHRASE
>
> and I've successfully connected with my wifi network.
>
> # ifconfig
> lo Link encap:Local Loopback
> inet addr:127.0.0.1 Mask:255.0.0.0
> inet6 addr: ::1/128 Scope:Host
> UP LOOPBACK RUNNING MTU:65536 Metric:1
> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>
> wlan0 Link encap:Ethernet HWaddr 10:98:C3:5F:FB:F9
> inet addr:192.168.10.110 Bcast:192.168.10.255
> Mask:255.255.255.0
> inet6 addr: fd3a:e7f5:fc04:0:1298:c3ff:fe5f:fbf9/64 Scope:Global
> inet6 addr: fe80::1298:c3ff:fe5f:fbf9/64 Scope:Link
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> RX packets:8 errors:0 dropped:0 overruns:0 frame:0
> TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:1624 (1.5 KiB) TX bytes:1988 (1.9 KiB)
>
> # ping google.com
> PING google.com (216.58.215.78): 56 data bytes
> 64 bytes from 216.58.215.78: seq=0 ttl=116 time=29.594 ms
> 64 bytes from 216.58.215.78: seq=1 ttl=116 time=39.401 ms
> ^C
> --- google.com ping statistics ---
> 2 packets transmitted, 2 packets received, 0% packet loss
> round-trip min/avg/max = 29.594/34.497/39.401 ms
>
>
> Could you verify if it works well on your device?
>
> בתאריך יום ו׳, 9 באוק׳ 2020 ב-19:49 מאת Bartosz Bilas <
> b.bilas at grinn-global.com>:
>
>> Hello Shlomi,
>> On 08.10.2020 22:45, Shlomi Vaknin wrote:
>>
>> Hi Bartek,
>>
>> I pulled the latest commits, downloaded my patches from patchwork and
>> applied them. Then, I started a new out of tree build and everything is
>> working. You can find my sdcard image here:
>> https://drive.google.com/drive/folders/1_FwVtw70iPS_hz7yFiiOlhXiUKlsi9bH?usp=sharing
>>
>> This problem is very strange. Maybe you can check if your board's wifi is
>> working with an image that is known to work? Maybe the formal image from st?
>>
>> Regards,
>> Shlomi
>>
>> I've tested your image but the result is the same, see:
>>
>> [ 129.691504] cfg80211: Loading compiled-in X.509 certificates for
>> regulatory database
>> [ 129.740878] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
>> # [ 129.804593] brcmfmac: brcmf_fw_alloc_request: using
>> brcm/brcmfmac43430-sdio for chip BCM43430/1
>> [ 130.885129] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000):
>> clkctl 0x50
>> [ 131.911135] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000):
>> clkctl 0x50
>>
>> My board is:
>>
>> CPU: STM32MP157CAC Rev.B
>> Model: STMicroelectronics STM32MP157C-DK2 Discovery Board
>> Board: stm32mp1 in trusted mode (st,stm32mp157c-dk2)
>> Board: MB1272 Var2.0 Rev.C-01
>> DRAM: 512 MiB
>> Best
>> Bartek
>>
>> בתאריך יום ה׳, 8 באוק׳ 2020 ב-20:31 מאת Bartosz Bilas <
>> b.bilas at grinn-global.com>:
>>
>>> Hi Shlomi,
>>> On 07.10.2020 22:16, Shlomi Vaknin wrote:
>>>
>>> Hi Bartek,
>>>
>>> That is very strange, since it works for me:
>>>
>>>
>>> #############################################################################################################################
>>> Starting mdev... OK
>>> [ 4.168709] cfg80211: Loading compiled-in X.509 certificates for
>>> regulatory database
>>> [ 4.224122] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
>>> [ 4.288641] brcmfmac: brcmf_fw_alloc_request: using
>>> brcm/brcmfmac43430-sdio for chip BCM43430/1
>>> [ 4.486998] brcmfmac: brcmf_fw_alloc_request: using
>>> brcm/brcmfmac43430-sdio for chip BCM43430/1
>>> [ 4.501649] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available
>>> (err=-2), device may have limited channels available
>>> [ 4.536998] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM43430/1
>>> wl0: Oct 23 2017 03:55:53 version 7.45.98.38 (r674442 CY) FWID 01-e58d219f
>>>
>>> # ifconfig -a
>>> eth0 Link encap:Ethernet HWaddr 00:80:E1:42:58:DB
>>> BROADCAST MULTICAST MTU:1500 Metric:1
>>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>>> collisions:0 txqueuelen:1000
>>> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>>> Interrupt:49 Base address:0xe000
>>>
>>> lo Link encap:Local Loopback
>>> inet addr:127.0.0.1 Mask:255.0.0.0
>>> inet6 addr: ::1/128 Scope:Host
>>> UP LOOPBACK RUNNING MTU:65536 Metric:1
>>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>>> collisions:0 txqueuelen:1000
>>> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>>>
>>> sit0 Link encap:IPv6-in-IPv4
>>> NOARP MTU:1480 Metric:1
>>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>>> collisions:0 txqueuelen:1000
>>> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>>>
>>> wlan0 Link encap:Ethernet HWaddr 00:9D:6B:A6:BC:BA
>>> BROADCAST MULTICAST MTU:1500 Metric:1
>>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>>> collisions:0 txqueuelen:1000
>>> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>>>
>>> #############################################################################################################################
>>>
>>> The nvram configuration file was directly copied from the bsp layer of
>>> st in yocto (dunfell):
>>> https://github.com/STMicroelectronics/meta-st-stm32mp/blob/dunfell/recipes-kernel/linux-firmware/linux-firmware/brcmfmac43430-sdio.txt
>>>
>>> Regards,
>>> Shlomi
>>>
>>> So in that case we have to clarify our environments. Have you tested
>>> using the latest master branch or is it some tagged version? Could you do a
>>> clean build once again to be sure that you don't use any cached things? If
>>> you were able to attach your sdcard image I would test it using my device
>>> and check if it really works because I don't see what could be wrong with
>>> that series. I don't think that ST has changed something between HW
>>> revision but I'm not able to locate on PCB what revision exactly is my
>>> board (I guess ST hasn't written it on the soldermask).
>>>
>>>
>>> Best
>>> Bartek
>>>
>>>
>>> בתאריך יום ד׳, 7 באוק׳ 2020 ב-22:27 מאת Bartosz Bilas <
>>> b.bilas at grinn-global.com>:
>>>
>>>> Hi Shlomi,
>>>>
>>>> On 07.10.2020 21:13, Bartosz Bilas wrote:
>>>> >
>>>> > Hi Shlomi,
>>>> >
>>>> > On 07.10.2020 16:49, Shlomi Vaknin wrote:
>>>> >> Adding support for wifi for stm32mp157c-dk2 is achieved by using
>>>> >> another dts which includes the bindings for the wifi module.
>>>> >> In addition, a txt file for the wifi firmware was added.
>>>> >> This was copied from the yocto bsp layer of st.
>>>> >>
>>>> >> Signed-off-by: Shlomi Vaknin<shlomi.39sd at gmail.com>
>>>> >> ---
>>>> >> .../stm32mp157c-dk2/linux.config | 4 +-
>>>> >> .../overlay/boot/extlinux/extlinux.conf | 2 +-
>>>> >> .../brcmfmac43430-sdio.st,stm32mp157c-dk2.txt | 59
>>>> +++++++++++++++++++
>>>> >> .../stm32mp157c-dk2/stm32mp157c-dk2-wifi.dts | 32 ++++++++++
>>>> >> configs/stm32mp157c_dk2_defconfig | 7 ++-
>>>> >> 5 files changed, 100 insertions(+), 4 deletions(-)
>>>> >> create mode 100644
>>>> board/stmicroelectronics/stm32mp157c-dk2/overlay/lib/firmware/brcm/
>>>> brcmfmac43430-sdio.st,stm32mp157c-dk2.txt
>>>> >> create mode 100644
>>>> board/stmicroelectronics/stm32mp157c-dk2/stm32mp157c-dk2-wifi.dts
>>>> >>
>>>> >> diff --git a/board/stmicroelectronics/stm32mp157c-dk2/linux.config
>>>> b/board/stmicroelectronics/stm32mp157c-dk2/linux.config
>>>> >> index c03eb748b4..4beee3a708 100644
>>>> >> --- a/board/stmicroelectronics/stm32mp157c-dk2/linux.config
>>>> >> +++ b/board/stmicroelectronics/stm32mp157c-dk2/linux.config
>>>> >> @@ -24,8 +24,6 @@ CONFIG_HIGHMEM=y
>>>> >> CONFIG_FORCE_MAX_ZONEORDER=12
>>>> >> CONFIG_SECCOMP=y
>>>> >> # CONFIG_ATAGS is not set
>>>> >> -CONFIG_ZBOOT_ROM_TEXT=0x0
>>>> >> -CONFIG_ZBOOT_ROM_BSS=0x0
>>>> >> CONFIG_ARM_APPENDED_DTB=y
>>>> >> CONFIG_ARM_ATAG_DTB_COMPAT=y
>>>> >> CONFIG_VFP=y
>>>> >> @@ -45,6 +43,7 @@ CONFIG_UNIX=y
>>>> >> CONFIG_INET=y
>>>> >> CONFIG_CAN=y
>>>> >> CONFIG_CAN_M_CAN=y
>>>> >> +CONFIG_CFG80211=m
>>>> >> CONFIG_DEVTMPFS=y
>>>> >> CONFIG_DEVTMPFS_MOUNT=y
>>>> >> CONFIG_SIMPLE_PM_BUS=y
>>>> >> @@ -66,6 +65,7 @@ CONFIG_SMSC911X=y
>>>> >> CONFIG_STMMAC_ETH=y
>>>> >> CONFIG_DWMAC_DWC_QOS_ETH=y
>>>> >> CONFIG_MDIO_BITBANG=y
>>>> >> +CONFIG_BRCMFMAC=m
>>>> >> CONFIG_INPUT_JOYDEV=y
>>>> >> CONFIG_INPUT_EVDEV=y
>>>> >> CONFIG_INPUT_TOUCHSCREEN=y
>>>> >> diff --git
>>>> a/board/stmicroelectronics/stm32mp157c-dk2/overlay/boot/extlinux/extlinux.conf
>>>> b/board/stmicroelectronics/stm32mp157c-dk2/overlay/boot/extlinux/extlinux.conf
>>>> >> index 5b7f56ee77..a6595971a8 100644
>>>> >> ---
>>>> a/board/stmicroelectronics/stm32mp157c-dk2/overlay/boot/extlinux/extlinux.conf
>>>> >> +++
>>>> b/board/stmicroelectronics/stm32mp157c-dk2/overlay/boot/extlinux/extlinux.conf
>>>> >> @@ -1,4 +1,4 @@
>>>> >> label stm32mp157c-dk2-buildroot
>>>> >> kernel /boot/zImage
>>>> >> - devicetree /boot/stm32mp157c-dk2.dtb
>>>> >> + devicetree /boot/stm32mp157c-dk2-wifi.dtb
>>>> >> append root=/dev/mmcblk0p4 rootwait
>>>> >> diff --git
>>>> a/board/stmicroelectronics/stm32mp157c-dk2/overlay/lib/firmware/brcm/
>>>> brcmfmac43430-sdio.st,stm32mp157c-dk2.txt
>>>> b/board/stmicroelectronics/stm32mp157c-dk2/overlay/lib/firmware/brcm/
>>>> brcmfmac43430-sdio.st,stm32mp157c-dk2.txt
>>>> >> new file mode 100644
>>>> >> index 0000000000..b36de8837f
>>>> >> --- /dev/null
>>>> >> +++
>>>> b/board/stmicroelectronics/stm32mp157c-dk2/overlay/lib/firmware/brcm/
>>>> brcmfmac43430-sdio.st,stm32mp157c-dk2.txt
>>>> >> @@ -0,0 +1,59 @@
>>>> >> +# NVRAM file for BCM943430WLSELG
>>>> >> +# 2.4 GHz, 20 MHz BW mode
>>>> >> +
>>>> >> +# The following parameter values are just placeholders, need to be
>>>> updated.
>>>> >> +manfid=0x2d0
>>>> >> +prodid=0x0726
>>>> >> +vendid=0x14e4
>>>> >> +devid=0x43e2
>>>> >> +boardtype=0x0726
>>>> >> +boardrev=0x1202
>>>> >> +boardnum=22
>>>> >> +macaddr=00:90:4c:c5:12:38
>>>> >> +sromrev=11
>>>> >> +boardflags=0x00404201
>>>> >> +boardflags3=0x08000000
>>>> >> +xtalfreq=37400
>>>> >> +#xtalfreq=19200
>>>> >> +nocrc=1
>>>> >> +ag0=255
>>>> >> +aa2g=1
>>>> >> +ccode=ALL
>>>> >> +
>>>> >> +pa0itssit=0x20
>>>> >> +extpagain2g=0
>>>> >> +
>>>> >> +#PA parameters for 2.4GHz, measured at CHIP OUTPUT
>>>> >> +pa2ga0=-168,7161,-820
>>>> >> +AvVmid_c0=0x0,0xc8
>>>> >> +cckpwroffset0=5
>>>> >> +
>>>> >> +# PPR params
>>>> >> +maxp2ga0=84
>>>> >> +txpwrbckof=6
>>>> >> +cckbw202gpo=0
>>>> >> +legofdmbw202gpo=0x66111111
>>>> >> +mcsbw202gpo=0x77711111
>>>> >> +propbw202gpo=0xdd
>>>> >> +
>>>> >> +# OFDM IIR :
>>>> >> +ofdmdigfilttype=18
>>>> >> +ofdmdigfilttypebe=18
>>>> >> +# PAPD mode:
>>>> >> +papdmode=1
>>>> >> +papdvalidtest=1
>>>> >> +pacalidx2g=32
>>>> >> +papdepsoffset=-36
>>>> >> +papdendidx=61
>>>> >> +
>>>> >> +il0macaddr=00:90:4c:c5:12:38
>>>> >> +wl0id=0x431b
>>>> >> +
>>>> >> +deadman_to=0xffffffff
>>>> >> +# muxenab: 0x1 for UART enable, 0x2 for GPIOs, 0x8 for JTAG
>>>> >> +muxenab=0x1
>>>> >> +# CLDO PWM voltage settings - 0x4 - 1.1 volt
>>>> >> +#cldo_pwm=0x4
>>>> >> +
>>>> >> +#VCO freq 326.4MHz
>>>> >> +spurconfig=0x3
>>>> >> diff --git
>>>> a/board/stmicroelectronics/stm32mp157c-dk2/stm32mp157c-dk2-wifi.dts
>>>> b/board/stmicroelectronics/stm32mp157c-dk2/stm32mp157c-dk2-wifi.dts
>>>> >> new file mode 100644
>>>> >> index 0000000000..89747d2b5f
>>>> >> --- /dev/null
>>>> >> +++
>>>> b/board/stmicroelectronics/stm32mp157c-dk2/stm32mp157c-dk2-wifi.dts
>>>> >> @@ -0,0 +1,32 @@
>>>> >> +/dts-v1/;
>>>> >> +
>>>> >> +#include "stm32mp157c-dk2.dts"
>>>> >> +
>>>> >> +/ {
>>>> >> + wifi_pwrseq: wifi-pwrseq {
>>>> >> + compatible = "mmc-pwrseq-simple";
>>>> >> + reset-gpios = <&gpioh 4 GPIO_ACTIVE_LOW>;
>>>> >> + };
>>>> >> +};
>>>> >> +
>>>> >> +/* Wifi */
>>>> >> +&sdmmc2 {
>>>> >> + arm,primecell-periphid = <0x10153180>;
>>>> >> + pinctrl-names = "default", "opendrain", "sleep";
>>>> >> + pinctrl-0 = <&sdmmc2_b4_pins_a>;
>>>> >> + pinctrl-1 = <&sdmmc2_b4_od_pins_a>;
>>>> >> + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>;
>>>> >> + non-removable;
>>>> >> + st,neg-edge;
>>>> >> + bus-width = <4>;
>>>> >> + vmmc-supply = <&v3v3>;
>>>> >> + mmc-pwrseq = <&wifi_pwrseq>;
>>>> >> + #address-cells = <1>;
>>>> >> + #size-cells = <0>;
>>>> >> + status = "okay";
>>>> >> +
>>>> >> + brcmf: bcrmf at 1 {
>>>> >> + reg = <1>;
>>>> >> + compatible = "brcm,bcm4329-fmac";
>>>> >> + };
>>>> >> +};
>>>> >> diff --git a/configs/stm32mp157c_dk2_defconfig
>>>> b/configs/stm32mp157c_dk2_defconfig
>>>> >> index bf7b9868b1..9c2e436244 100644
>>>> >> --- a/configs/stm32mp157c_dk2_defconfig
>>>> >> +++ b/configs/stm32mp157c_dk2_defconfig
>>>> >> @@ -9,8 +9,13 @@ BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.8.13"
>>>> >> BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
>>>> >>
>>>> BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/stmicroelectronics/stm32mp157c-dk2/linux.config"
>>>> >> BR2_LINUX_KERNEL_DTS_SUPPORT=y
>>>> >> -BR2_LINUX_KERNEL_INTREE_DTS_NAME="stm32mp157c-dk2"
>>>> >>
>>>> +BR2_LINUX_KERNEL_CUSTOM_DTS_PATH="board/stmicroelectronics/stm32mp157c-dk2/stm32mp157c-dk2-wifi.dts"
>>>> >> BR2_LINUX_KERNEL_INSTALL_TARGET=y
>>>> >> +BR2_PACKAGE_LINUX_FIRMWARE=y
>>>> >> +BR2_PACKAGE_LINUX_FIRMWARE_BRCM_BCM43XXX=y
>>>> >> +BR2_PACKAGE_WIRELESS_REGDB=y
>>>> >> +BR2_PACKAGE_WPA_SUPPLICANT=y
>>>> >> +BR2_PACKAGE_WPA_SUPPLICANT_CLI=y
>>>> >> BR2_TARGET_ROOTFS_EXT2=y
>>>> >> BR2_TARGET_ROOTFS_EXT2_4=y
>>>> >> BR2_TARGET_ROOTFS_EXT2_SIZE="120M"
>>>>
>>>> I suggest to add BR2_ROOTFS_DEVICE_CREATION_DYNAMIC_MDEV to load
>>>> firmware and driver automatically on boot.
>>>>
>>>> Unfortunately it doesn't work for me, see:
>>>>
>>>> [ 4.186415] cfg80211: Loading compiled-in X.509 certificates for
>>>> regulatory database
>>>> [ 4.237180] cfg80211: Loaded X.509 cert 'sforshee:
>>>> 00b28ddf47aef9cea7'
>>>> [ 4.300765] brcmfmac: brcmf_fw_alloc_request: using
>>>> brcm/brcmfmac43430-sdio for chip BCM43430/1
>>>> [ 5.389412] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000):
>>>> clkctl 0x50
>>>> [ 6.407710] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000):
>>>> clkctl 0x50
>>>>
>>>> Google says that it could be due to wrong nvram file configuration but
>>>> I
>>>> assume that you have run it successfully?
>>>>
>>>> # ifconfig -a
>>>> eth0 Link encap:Ethernet HWaddr 00:80:E1:42:56:44
>>>> BROADCAST MULTICAST MTU:1500 Metric:1
>>>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>>>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>>>> collisions:0 txqueuelen:1000
>>>> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>>>> Interrupt:49 Base address:0xe000
>>>>
>>>> lo Link encap:Local Loopback
>>>> inet addr:127.0.0.1 Mask:255.0.0.0
>>>> inet6 addr: ::1/128 Scope:Host
>>>> UP LOOPBACK RUNNING MTU:65536 Metric:1
>>>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>>>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>>>> collisions:0 txqueuelen:1000
>>>> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>>>>
>>>> sit0 Link encap:IPv6-in-IPv4
>>>> NOARP MTU:1480 Metric:1
>>>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>>>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>>>> collisions:0 txqueuelen:1000
>>>> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>>>>
>>>> #
>>>>
>>>> As you can see there is no wlan0 interface.
>>>>
>>>> Best
>>>> Bartek
>>>>
>>>
>>> _______________________________________________
>>> buildroot mailing listbuildroot at busybox.nethttp://lists.busybox.net/mailman/listinfo/buildroot
>>>
>>>
> _______________________________________________
> buildroot mailing listbuildroot at busybox.nethttp://lists.busybox.net/mailman/listinfo/buildroot
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.busybox.net/pipermail/buildroot/attachments/20201010/01f56385/attachment.html>
More information about the buildroot
mailing list