[Buildroot] [EXT] Re: [PATCH v3 9/9] configs/nxp_ls1028ardb*: new board
Jerry Huang
jerry.huang at nxp.com
Fri Dec 6 08:20:19 UTC 2019
Best Regards
Jerry Huang
> -----Original Message-----
> From: Vladimir Oltean <olteanv at gmail.com>
> Sent: Tuesday, December 3, 2019 9:49 AM
> To: Jerry Huang <jerry.huang at nxp.com>
> Cc: buildroot at busybox.net; Michael Walle <michael at walle.cc>;
> geomatsi at gmail.com; matthew.weber at collins.com; Thomas Petazzoni
> <thomas.petazzoni at bootlin.com>
> Subject: [EXT] Re: [Buildroot] [PATCH v3 9/9] configs/nxp_ls1028ardb*: new
> board
>
> Caution: EXT Email
>
> On Wed, 27 Nov 2019 at 09:18, Changming Huang <jerry.huang at nxp.com>
> wrote:
> >
> > This is to support Freescale/NXP LS1028ARDB in Buildroot.
> > The board is setup to track the Linux at 4.19 via NXP LSDK-19.09.
> >
> > The target will build uboot and RCW binary with arm-trusted-firmware
> support.
> >
> > board/nxp/ls1028ardb/: scripts related with ls1028ardb
> > nxp_ls1028ardb-64b-emmc_defconfig: defconfig boot from emmc chip on
> > board
> > nxp_ls1028ardb-64b_defconfig: defconfig boot from SD card
> > nxp_ls1028ardb-64b-xspi_defconfig: defconfig boot from FlexSPI chip on
> > board
> >
> > Signed-off-by: Changming Huang <jerry.huang at nxp.com>
> > ---
> > changes since v2:
> > 1. Modify the qoriq-cadence-dp-firmware option in defconfig.
> > 2. rename defconfig to nxp_ls1028*.
> > 3. remove extra packages except busybox in defconfig.
> > 4. modify the description of file genimage.xspi.cfg.template.
> >
> > changes since v1:
> > 1. add new option in configs/freescale_ls1028ardb-xxxx_defconfig.
> > ---
> > .gitlab-ci.yml | 3 +
> > DEVELOPERS | 2 +
> > .../nxp/ls1028ardb/genimage.emmc.cfg.template | 52 ++++++++++++
> > board/nxp/ls1028ardb/genimage.sd.cfg.template | 52 ++++++++++++
> > .../nxp/ls1028ardb/genimage.xspi.cfg.template | 55 ++++++++++++
> > board/nxp/ls1028ardb/kernel.its | 59 +++++++++++++
> > board/nxp/ls1028ardb/ls1028-10-network.rules | 16 ++++
> > board/nxp/ls1028ardb/post-cfg-udev.sh | 10 +++
> > board/nxp/ls1028ardb/readme.txt | 61 +++++++++++++
> > .../ls1028ardb/u-boot-environment-emmc.txt | 22 +++++
> > .../nxp/ls1028ardb/u-boot-environment-sd.txt | 21 +++++
> > .../ls1028ardb/u-boot-environment-xspi.txt | 22 +++++
> > configs/nxp_ls1028ardb-64b-emmc_defconfig | 85
> +++++++++++++++++++
> > configs/nxp_ls1028ardb-64b-xspi_defconfig | 85
> +++++++++++++++++++
> > configs/nxp_ls1028ardb-64b_defconfig | 85
> +++++++++++++++++++
> > 15 files changed, 630 insertions(+)
> > create mode 100644 board/nxp/ls1028ardb/genimage.emmc.cfg.template
> > create mode 100644 board/nxp/ls1028ardb/genimage.sd.cfg.template
> > create mode 100644 board/nxp/ls1028ardb/genimage.xspi.cfg.template
> > create mode 100644 board/nxp/ls1028ardb/kernel.its create mode
> > 100644 board/nxp/ls1028ardb/ls1028-10-network.rules
> > create mode 100755 board/nxp/ls1028ardb/post-cfg-udev.sh
> > create mode 100644 board/nxp/ls1028ardb/readme.txt create mode
> > 100644 board/nxp/ls1028ardb/u-boot-environment-emmc.txt
> > create mode 100644 board/nxp/ls1028ardb/u-boot-environment-sd.txt
> > create mode 100644 board/nxp/ls1028ardb/u-boot-environment-xspi.txt
> > create mode 100644 configs/nxp_ls1028ardb-64b-emmc_defconfig
> > create mode 100644 configs/nxp_ls1028ardb-64b-xspi_defconfig
> > create mode 100644 configs/nxp_ls1028ardb-64b_defconfig
> >
> > diff --git a/.gitlab-ci.yml b/.gitlab-ci.yml index
> > 22befa0427..08e6360ff7 100644
> > --- a/.gitlab-ci.yml
> > +++ b/.gitlab-ci.yml
> > @@ -223,6 +223,9 @@ nitrogen6sx_defconfig: { extends: .defconfig }
> > nitrogen6x_defconfig: { extends: .defconfig }
> > nitrogen7_defconfig: { extends: .defconfig }
> > nitrogen8m_defconfig: { extends: .defconfig }
> > +nxp_ls1028ardb-64b-emmc_defconfig: { extends: .defconfig }
> > +nxp_ls1028ardb-64b_defconfig: { extends: .defconfig }
> > +nxp_ls1028ardb-64b-xspi_defconfig: { extends: .defconfig }
> > odroidxu4_defconfig: { extends: .defconfig }
> > olimex_a10_olinuxino_lime_defconfig: { extends: .defconfig }
> > olimex_a13_olinuxino_defconfig: { extends: .defconfig } diff --git
> > a/DEVELOPERS b/DEVELOPERS index 6fd8f8ee08..efe4039194 100644
> > --- a/DEVELOPERS
> > +++ b/DEVELOPERS
> > @@ -515,6 +515,8 @@ F: configs/orangepi_plus_defconfig
> >
> > N: Changming Huang <jerry.huang at nxp.com>
> > F: board/nxp/common/ls/
> > +F: board/nxp/ls1028ardb/
> > +F: configs/nxp_ls1028ardb*
> > F: package/nxp/qoriq-cadence-dp-firmware/
> >
> > N: Chris Packham <judge.packham at gmail.com>
> > diff --git a/board/nxp/ls1028ardb/genimage.emmc.cfg.template
> > b/board/nxp/ls1028ardb/genimage.emmc.cfg.template
> > new file mode 100644
> > index 0000000000..3afbda494e
> > --- /dev/null
> > +++ b/board/nxp/ls1028ardb/genimage.emmc.cfg.template
> > @@ -0,0 +1,52 @@
> > +# Minimal eMMC boot image for the NXP boards Template # # eMMC image
> > +(sdcard.img) format:
> > +# * the eMMC must have 4 kB free space at the beginning, # * U-Boot
> > +is dumped as is, # * a FAT partition at offset 64 MB is containing
> > +Image and DTB files # * a single root filesystem partition is
> > +required (ext2, ext3 or ext4) #
> > +
> > +image boot.vfat {
> > + vfat {
> > + files = {
> > + %FILES%
> > + }
> > + }
> > + size = 256M
> > +}
> > +
> > +image sdcard.img {
> > + hdimage {
> > + }
> > +
> > + partition rcw {
> > + in-partition-table = "no"
> > + image = "bl2_emmc.pbl"
> > + offset = 4096
> > + }
> > +
> > + partition u-boot {
> > + in-partition-table = "no"
> > + image = "fip.bin"
> > + offset = 1M
> > + }
> > +
> > + partition u-boot-environment {
> > + in-partition-table = "no"
> > + image = "uboot-env.bin"
> > + offset = 5M
> > + }
> > +
> > + partition boot {
> > + partition-type = 0xC
> > + bootable = "true"
> > + image = "boot.vfat"
> > + offset = 64M
> > + }
> > +
> > + partition rootfs {
> > + partition-type = 0x83
> > + image = "rootfs.ext2"
> > + }
> > +}
> > diff --git a/board/nxp/ls1028ardb/genimage.sd.cfg.template
> > b/board/nxp/ls1028ardb/genimage.sd.cfg.template
> > new file mode 100644
> > index 0000000000..ab50e103c1
> > --- /dev/null
> > +++ b/board/nxp/ls1028ardb/genimage.sd.cfg.template
> > @@ -0,0 +1,52 @@
> > +# Minimal SD card image for the NXP boards Template # # SD card image
> > +(sdcard.img) format:
> > +# * the SD card must have 4 kB free space at the beginning, # *
> > +U-Boot is dumped as is, # * a FAT partition at offset 64 MB is
> > +containing Image and DTB files # * a single root filesystem partition
> > +is required (ext2, ext3 or ext4) #
> > +
> > +image boot.vfat {
> > + vfat {
> > + files = {
> > + %FILES%
> > + }
> > + }
> > + size = 256M
> > +}
> > +
> > +image sdcard.img {
> > + hdimage {
> > + }
> > +
> > + partition rcw {
> > + in-partition-table = "no"
> > + image = "bl2_sd.pbl"
> > + offset = 4096
> > + }
> > +
> > + partition u-boot {
> > + in-partition-table = "no"
> > + image = "fip.bin"
> > + offset = 1M
> > + }
> > +
> > + partition u-boot-environment {
> > + in-partition-table = "no"
> > + image = "uboot-env.bin"
> > + offset = 5M
> > + }
> > +
> > + partition boot {
> > + partition-type = 0xC
> > + bootable = "true"
> > + image = "boot.vfat"
> > + offset = 64M
> > + }
> > +
> > + partition rootfs {
> > + partition-type = 0x83
> > + image = "rootfs.ext2"
> > + }
> > +}
> > diff --git a/board/nxp/ls1028ardb/genimage.xspi.cfg.template
> > b/board/nxp/ls1028ardb/genimage.xspi.cfg.template
> > new file mode 100644
> > index 0000000000..1bc3a4ec49
> > --- /dev/null
> > +++ b/board/nxp/ls1028ardb/genimage.xspi.cfg.template
> > @@ -0,0 +1,55 @@
> > +# Minimal XSPI (FlexSPI) image for the NXP boards Template # #
> > +FlexSPI image (xspi.cpio.img) format:
> > +# * For ls1028ardb, the FlexSPI flash size is 256MB, erase size is
> > +128KB # * bl2_flexspi_nor.bpl: the RCW with ATF header # * fib.bin:
> > +u-boot-dtb.bin binary with ATF header # * Kernel.itb:
> > +# * offset 16MB, include Kernel, ramdisk file system and DTB file
> > +#
> > +flash xspi-256M-128K {
> > + pebsize = 128K
> > + numpebs = 2048
> > + minimum-io-unit-size = 128k
> > +}
> > +
> > +image xspi.cpio.img {
> > + flash {
> > + }
> > + flashtype = "xspi-256M-128K"
> > +
> > + partition rcw {
> > + in-partition-table = "no"
> > + image = "bl2_flexspi_nor.pbl"
> > + offset = 0
> > + size = 1M
> > + }
> > +
> > + partition u-boot {
> > + in-partition-table = "no"
> > + image = "fip.bin"
> > + offset = 1M
> > + size = 4M
> > + }
> > +
> > + partition u-boot-environment {
> > + in-partition-table = "no"
> > + image = "uboot-env.bin"
> > + offset = 5M
> > + size = 1M
> > + }
> > +
> > + partition dp-firmware {
> > + in-partition-table = "no"
> > + image = "ls1028a-dp-fw.bin"
> > + offset = 0x940000
> > + size = 256K
> > + }
> > +
> > + partition boot {
> > + in-partition-table = "no"
> > + image = "kernel.itb"
> > + offset = 16M
> > + size = 48M
> > + }
> > +}
> > diff --git a/board/nxp/ls1028ardb/kernel.its
> > b/board/nxp/ls1028ardb/kernel.its new file mode 100644 index
> > 0000000000..08e9700f30
> > --- /dev/null
> > +++ b/board/nxp/ls1028ardb/kernel.its
> > @@ -0,0 +1,59 @@
> > +/*
> > + * Copyright 2019 NXP
> > + *
> > + * Changming Huang <jerry.huang at nxp.com>
> > + *
> > + * SPDX-License-Identifier: GPL-2.0+
> > + */
> > +
> > +/dts-v1/;
> > +
> > +/ {
> > + description = "Image file for the LS1028A Linux Kernel";
> > + #address-cells = <1>;
> > +
> > + images {
> > + kernel at 1 {
> > + description = "ARM64 Linux kernel";
> > + data = /incbin/("./Image.gz");
> > + type = "kernel";
> > + arch = "arm64";
> > + os = "linux";
> > + compression = "gzip";
> > + load = <0x80080000>;
> > + entry = <0x80080000>;
> > + };
> > + fdt at 1 {
> > + description = "Flattened Device Tree blob";
> > + data = /incbin/("./fsl-ls1028a-rdb.dtb");
> > + type = "flat_dt";
> > + arch = "arm64";
> > + compression = "none";
> > + load = <0x90000000>;
> > + };
> > + ramdisk at 1 {
> > + description = "LS1028 Ramdisk";
> > + data = /incbin/("./rootfs.cpio.gz");
> > + type = "ramdisk";
> > + arch = "arm64";
> > + os = "linux";
> > + compression = "gzip";
> > + };
> > + };
> > +
> > + configurations {
> > + default = "config at 1";
> > + config at 1 {
> > + description = "Boot Linux kernel";
> > + kernel = "kernel at 1";
> > + fdt = "fdt at 1";
> > + ramdisk = "ramdisk at 1";
> > + };
> > + ls1028ardb {
> > + description = "Boot Linux kernel";
> > + kernel = "kernel at 1";
> > + fdt = "fdt at 1";
> > + ramdisk = "ramdisk at 1";
> > + };
> > + };
> > +};
> > diff --git a/board/nxp/ls1028ardb/ls1028-10-network.rules
> > b/board/nxp/ls1028ardb/ls1028-10-network.rules
> > new file mode 100644
> > index 0000000000..19f41634bd
> > --- /dev/null
> > +++ b/board/nxp/ls1028ardb/ls1028-10-network.rules
> > @@ -0,0 +1,16 @@
> > +# ENETC rules
> > +ACTION=="add", SUBSYSTEM=="net", KERNELS=="0000:00:00.0",
> DRIVERS=="fsl_enetc", NAME:="eno0"
> > +ACTION=="add", SUBSYSTEM=="net", KERNELS=="0000:00:00.1",
> DRIVERS=="fsl_enetc", NAME:="eno1"
> > +ACTION=="add", SUBSYSTEM=="net", KERNELS=="0000:00:00.2",
> DRIVERS=="fsl_enetc", NAME:="eno2"
> > +ACTION=="add", SUBSYSTEM=="net", KERNELS=="0000:00:00.6",
> DRIVERS=="fsl_enetc", NAME:="eno3"
> > +ACTION=="add", SUBSYSTEM=="net", KERNELS=="0000:00:01.0",
> DRIVERS=="fsl_enetc_vf", NAME:="eno0vf0"
> > +ACTION=="add", SUBSYSTEM=="net", KERNELS=="0000:00:01.1",
> DRIVERS=="fsl_enetc_vf", NAME:="eno0vf1"
> > +ACTION=="add", SUBSYSTEM=="net", KERNELS=="0000:00:01.2",
> DRIVERS=="fsl_enetc_vf", NAME:="eno1vf0"
> > +ACTION=="add", SUBSYSTEM=="net", KERNELS=="0000:00:01.3",
> DRIVERS=="fsl_enetc_vf", NAME:="eno1vf1"
> > +# LS1028 switch rules
> > +ACTION=="add", SUBSYSTEM=="net", KERNELS=="0000:00:00.5",
> DRIVERS=="mscc_felix", ATTR{phys_port_name}=="p0", NAME="swp0"
> > +ACTION=="add", SUBSYSTEM=="net", KERNELS=="0000:00:00.5",
> DRIVERS=="mscc_felix", ATTR{phys_port_name}=="p1", NAME="swp1"
> > +ACTION=="add", SUBSYSTEM=="net", KERNELS=="0000:00:00.5",
> DRIVERS=="mscc_felix", ATTR{phys_port_name}=="p2", NAME="swp2"
> > +ACTION=="add", SUBSYSTEM=="net", KERNELS=="0000:00:00.5",
> DRIVERS=="mscc_felix", ATTR{phys_port_name}=="p3", NAME="swp3"
> > +ACTION=="add", SUBSYSTEM=="net", KERNELS=="0000:00:00.5",
> DRIVERS=="mscc_felix", ATTR{phys_port_name}=="p4", NAME="swp4"
> > +ACTION=="add", SUBSYSTEM=="net", KERNELS=="0000:00:00.5",
> DRIVERS=="mscc_felix", ATTR{phys_port_name}=="p5", NAME="swp5"
> > diff --git a/board/nxp/ls1028ardb/post-cfg-udev.sh
> > b/board/nxp/ls1028ardb/post-cfg-udev.sh
> > new file mode 100755
> > index 0000000000..311a93aee2
> > --- /dev/null
> > +++ b/board/nxp/ls1028ardb/post-cfg-udev.sh
> > @@ -0,0 +1,10 @@
> > +#!/usr/bin/env bash
> > +
> > +main()
> > +{
> > + cp board/nxp/ls1028ardb/ls1028-10-network.rules
> > +${TARGET_DIR}/etc/udev/rules.d/10-network.rules
>
> Shouldn't this be a part of a BR2_ROOTFS_OVERLAY fragment?
>
> > +
> > + exit $?
> > +}
> > +
> > +main $@
> > diff --git a/board/nxp/ls1028ardb/readme.txt
> > b/board/nxp/ls1028ardb/readme.txt new file mode 100644 index
> > 0000000000..713babd7c3
> > --- /dev/null
> > +++ b/board/nxp/ls1028ardb/readme.txt
> > @@ -0,0 +1,61 @@
> > +LS1028ARDB board is one platform based on LS1028A silicon for
> > +industry, which is supported in LSDK-19.09.
> > +
> > +One simple image file is created by buildroot, which includes RCW,
> > +uboot, Linux kernel, rootfs and other necessary binaries for this board.
> > +
> > +To program the image file created by buildroot into the flash.
> > +There are two way to do it:
> > +
> > +1. Program the image file on PC machine for SD card boot
> > + $ sudo dd if=./output/images/sdcard.img of=/dev/sdx
> > + # or in some other host machine:
> > + $ sudo dd if=./output/images/sdcard.img of=/dev/mmcblkx
> > +
> > + # find the right SD Card device name in your host machine and
> > + replace the # “sdx” or “mmcblkx”.
> > +
> > +2. Program the image file on board for eMMC and XSPI boot Make sure
> > +your board has ipaddr, netmask, and serverip defined to reach your
> > +tftp server.
> > +
> > + 2.1 Program eMMC boot image file to eMMC chip
> > + # Make sure output/images/sdcard.img is stored to tftp server
> > + # Below command is one example
> > + => tftpboot 0xa0000000 sdcard.img
> > + => mmc dev 1
> > + => mmc erase 0 0x200000
> > + => mmc write 0xa0000000 0 0x200000
> > +
> > + # The size "0x200000" will be changed when the image size is different.
> > +
> > + 2.2 Program XSPI boot image file to flash
> > + # Make sure output/images/xspi.cpio.img is stored to tftp server
> > + # Below command is one example
> > + => tftpboot 0xa0000000 xspi.cpio.img
> > + => sf probe
> > + => sf erase 0 $filesize
> > + => sf write 0xa0000000 0 $filesize
> > +
> > +3. Booting your new system
> > +Before booting the new system, we should make sure the switch setting is
> right.
> > +below switch setting is for each booting mode:
> > + +-----------+---------------------+
> > + |Boot mode | Switch setting |
> > + +---------------------------------+
> > + |SD boot | SW2[1~4] = 0b’1000 |
> > + +---------------------------------+
> > + |eMMC boot | SW2[1~4] = 0b’1001 |
> > + +---------------------------------+
> > + |XSPI boot | SW2[1~4] = 0b’1111 |
> > + +-----------+---------------------+
> > +
> > +or we use following command to reset the board in uboot prompt:
> > + # boot from SD card
> > + => qixis_reset sd
> > +
> > + # boot from eMMC chip
> > + => qixis_reset emmc
> > +
> > + # boot from XSPI
> > + => qixis_reset qspi
> > diff --git a/board/nxp/ls1028ardb/u-boot-environment-emmc.txt
> > b/board/nxp/ls1028ardb/u-boot-environment-emmc.txt
> > new file mode 100644
> > index 0000000000..01a97aa89d
> > --- /dev/null
> > +++ b/board/nxp/ls1028ardb/u-boot-environment-emmc.txt
> > @@ -0,0 +1,22 @@
> > +baudrate=115200
> > +bootcmd=setenv bootargs root=/dev/mmcblk1p2 rootwait rw
> > +earlycon=uart8250,0x21c0500 console=ttyS0,115200 cma=256M
> > +video=1920x1080-32 at 60;mmc dev 1;mmcinfo;fatload mmc 1:1 ${dp_load}
> > +${dp_file};hdp load ${dp_load} ${dp_offset};fatload mmc 1:1
> > +${loadaddr} ${bootfile};fatload mmc 1:1 ${fdtaddr} ${fdtfile};booti
> > +${loadaddr} - ${fdtaddr}
> > +bootdelay=3
> > +bootfile=Image
> > +fdtfile=fsl-ls1028a-rdb.dtb
> > +eth2addr=00:1F:7B:63:35:E9
>
> Do we really want to put a MAC address in the U-Boot environment? This will
> work ok for the first board, but not so well for the second board that you put in
> the same network.
> And actually, do we want a U-Boot environment at all? The LSDK U-Boot default
> environment is distroboot enabled. With the proper extlinux.conf file generated
> by post-image.sh, it can load Buildroot in a breeze with no custom script
> necessary:
I can remove the MAC address from u-boot environment, uboot will use the random MAC address if there is not.
Actually, MAC address should be written to EEPROM.
Though, the environment is enabled in LSDK U-Boot, but it is for all boot modes which cause the boot scripts is very complex and not easy to read.
So we use the environment simplified.
> label Buildroot %VERSION% - %BOARD%
> kernel %KERNEL%
> devicetree %DTB%
> append console=ttyS0,115200n8 root=/dev/mmcblk0p2 rw rootwait
>
> > +ethact=FM1 at DTSEC3
> > +ethprime=FM1 at DTSEC3
>
> There is certainly no DTSEC port on LS1028A.
>
> > +fdt_high=0xffffffffffffffff
> > +fdtcontroladdr=ffc01550
> > +fman_ucode=ffc12090
>
> And no FMan microcode.
>
> > +hwconfig=fsl_ddr:bank_intlv=auto
> > +initrd_high=0xffffffffffffffff
> > +loadaddr=0xa0000000
> > +fdtaddr=0xb0000000
> > +dp_file=ls1028a-dp-fw.bin
> > +dp_load=0x90000000
> > +dp_offset=0x2000
> > +stderr=serial
> > +stdin=serial
> > +stdout=serial
> > +rollbackboot=setenv bootargs root=/dev/ram0 rootwait rw
> > +earlycon=uart8250,0x21c0500 console=ttyS0,115200;mmcinfo;fatload mmc
> > +0:1 ${loadaddr} ${bootfile};bootm ${loadaddr}
>
> What does "rollbackboot" do?
>
> > diff --git a/board/nxp/ls1028ardb/u-boot-environment-sd.txt
> > b/board/nxp/ls1028ardb/u-boot-environment-sd.txt
> > new file mode 100644
> > index 0000000000..820989280f
> > --- /dev/null
> > +++ b/board/nxp/ls1028ardb/u-boot-environment-sd.txt
> > @@ -0,0 +1,21 @@
> > +baudrate=115200
> > +bootcmd=setenv bootargs root=/dev/mmcblk0p2 rootwait rw
> > +earlycon=uart8250,0x21c0500 console=ttyS0,115200 cma=256M
> > +video=1920x1080-32 at 60;mmcinfo;fatload mmc 0:1 ${dp_load} ${dp_file};
> > +hdp load ${dp_load} ${dp_offset};fatload mmc 0:1 ${loadaddr}
> > +${bootfile};fatload mmc 0:1 ${fdtaddr} ${fdtfile};booti ${loadaddr} -
> > +${fdtaddr}
> > +bootdelay=3
> > +bootfile=Image
> > +fdtfile=fsl-ls1028a-rdb.dtb
> > +eth2addr=00:1F:7B:63:35:E9
> > +ethact=FM1 at DTSEC3
> > +ethprime=FM1 at DTSEC3
> > +fdt_high=0xffffffffffffffff
> > +fdtcontroladdr=ffc01550
> > +fman_ucode=ffc12090
> > +hwconfig=fsl_ddr:bank_intlv=auto
> > +initrd_high=0xffffffffffffffff
> > +loadaddr=0xa0000000
> > +fdtaddr=0xb0000000
> > +dp_file=ls1028a-dp-fw.bin
> > +dp_load=0x90000000
> > +dp_offset=0x2000
> > +stderr=serial
> > +stdin=serial
> > +stdout=serial
> > diff --git a/board/nxp/ls1028ardb/u-boot-environment-xspi.txt
> > b/board/nxp/ls1028ardb/u-boot-environment-xspi.txt
> > new file mode 100644
> > index 0000000000..5677cdddaa
> > --- /dev/null
> > +++ b/board/nxp/ls1028ardb/u-boot-environment-xspi.txt
> > @@ -0,0 +1,22 @@
> > +baudrate=115200
> > +bootcmd=setenv bootargs root=/dev/ram0 rw
> earlycon=uart8250,0x21c0500
> > +console=ttyS0,115200 cma=256M video=1920x1080-32 at 60; sf probe 0:0; sf
> > +read $dp_load $dp_start $dp_size; hdp load $dp_load $dp_offset; sf
> > +read $kernel_load $kernel_start $kernel_size && bootm $kernel_load
> > +bootdelay=3
> > +eth2addr=00:1F:7B:63:35:E9
> > +ethact=FM1 at DTSEC3
> > +ethprime=FM1 at DTSEC3
> > +fdt_high=0xffffffffffffffff
> > +fdtcontroladdr=ffc01550
> > +fman_ucode=ffc12090
> > +hwconfig=fsl_ddr:bank_intlv=auto
> > +initrd_high=0xffffffffffffffff
> > +kernel_load=0xa0000000
> > +kernel_size=0x3000000
> > +kernel_start=0x1000000
> > +dp_load=0x90000000
> > +dp_start=0x940000
> > +dp_size=0x40000
> > +dp_offset=0x2000
> > +stderr=serial
> > +stdin=serial
> > +stdout=serial
> > +rollbackboot=setenv bootargs root=/dev/ram0 rootwait rw
> > +earlycon=uart8250,0x21c0500 console=ttyS0,115200;mmcinfo;fatload mmc
> > +0:1 ${loadaddr} ${bootfile};bootm $loadaddr
> > diff --git a/configs/nxp_ls1028ardb-64b-emmc_defconfig
> > b/configs/nxp_ls1028ardb-64b-emmc_defconfig
> > new file mode 100644
> > index 0000000000..019889f5e0
> > --- /dev/null
> > +++ b/configs/nxp_ls1028ardb-64b-emmc_defconfig
>
> Thomas, is there any way in Buildroot to use fragments for the board configs, to
> avoid duplication? I couldn't find any way.
>
> > @@ -0,0 +1,85 @@
> > +# Architecture
> > +BR2_aarch64=y
> > +BR2_cortex_a72=y
> > +
> > +# Filesystem
> > +BR2_TARGET_ROOTFS_EXT2=y
> > +BR2_TARGET_ROOTFS_EXT2_4=y
> > +
> > +# Hostname and issue
> > +BR2_TARGET_GENERIC_HOSTNAME="LS1028ARDB"
> > +
> > +# toolchain
> > +BR2_TOOLCHAIN_BUILDROOT_GLIBC=y
> > +BR2_TOOLCHAIN_BUILDROOT_LIBC="glibc"
> > +
> > +# Linux headers same as kernel
> > +BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_19=y
> > +
> > +# bootloader
> > +BR2_TARGET_UBOOT=y
> > +BR2_TARGET_UBOOT_FORMAT_DTB_BIN=y
> > +BR2_TARGET_UBOOT_BOARDNAME="ls1028ardb_tfa"
> > +BR2_TARGET_UBOOT_CUSTOM_GIT=y
> >
> +BR2_TARGET_UBOOT_CUSTOM_REPO_URL="https://eur01.safelinks.protectio
> n.outlook.com/?url=https%3A%2F%2Fsource.codeaurora.org%2Fexternal%2Fqo
> riq%2Fqoriq-components%2Fu-boot&data=02%7C01%7Cjerry.huang%40nx
> p.com%7Cae8709aebdf54eef25ed08d77792f39a%7C686ea1d3bc2b4c6fa92cd9
> 9c5c301635%7C0%7C0%7C637109345348800651&sdata=kFn3nsvOHgCCT
> JYKYMoU9rRkGsFR77TYGzbvOEezXIg%3D&reserved=0"
> > +BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="LSDK-19.09"
> > +BR2_TARGET_UBOOT_NEEDS_DTC=y
> > +BR2_TARGET_UBOOT_FORMAT_BIN=n
> > +BR2_TARGET_UBOOT_FORMAT_CUSTOM=y
> > +BR2_TARGET_UBOOT_FORMAT_CUSTOM_NAME="u-boot-dtb.bin"
> > +BR2_PACKAGE_UBOOT_TOOLS_MKIMAGE=y
> > +BR2_TARGET_UBOOT_ENVIMAGE=y
> >
> +BR2_TARGET_UBOOT_ENVIMAGE_SOURCE="board/nxp/ls1028ardb/u-boot-e
> nvironment-emmc.txt"
> > +BR2_TARGET_UBOOT_ENVIMAGE_SIZE="0x2000"
> > +
> > +# Kernel
> > +BR2_LINUX_KERNEL=y
> > +BR2_LINUX_KERNEL_CUSTOM_GIT=y
> >
> +BR2_LINUX_KERNEL_CUSTOM_REPO_URL="https://eur01.safelinks.protection
> .outlook.com/?url=https%3A%2F%2Fsource.codeaurora.org%2Fexternal%2Fqor
> iq%2Fqoriq-components%2Flinux&data=02%7C01%7Cjerry.huang%40nxp.
> com%7Cae8709aebdf54eef25ed08d77792f39a%7C686ea1d3bc2b4c6fa92cd99c
> 5c301635%7C0%7C0%7C637109345348800651&sdata=iS%2F%2Bf1lVYF9f
> PRlNdjKkKKuRmRsdwtOTF7mZ%2BUFwz5c%3D&reserved=0"
> > +BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="LSDK-19.09-V4.19"
> > +BR2_LINUX_KERNEL_USE_ARCH_DEFAULT_CONFIG=y
> >
> +BR2_LINUX_KERNEL_CONFIG_FRAGMENT_FILES="$(LINUX_DIR)/arch/arm64
> /configs/lsdk.config"
> > +BR2_LINUX_KERNEL_DTS_SUPPORT=y
> > +BR2_LINUX_KERNEL_INTREE_DTS_NAME="freescale/fsl-ls1028a-rdb"
> > +BR2_LINUX_KERNEL_IMAGE_TARGET_CUSTOM=y
> > +BR2_LINUX_KERNEL_IMAGE_TARGET_NAME="Image"
> > +
> > +# Serial port config
> > +BR2_TARGET_GENERIC_GETTY=y
> > +BR2_TARGET_GENERIC_GETTY_PORT="ttyS0"
> > +
> > +# required tools to create the microSD image
> > +BR2_PACKAGE_HOST_DOSFSTOOLS=y BR2_PACKAGE_HOST_GENIMAGE=y
> > +BR2_PACKAGE_HOST_MTOOLS=y
> > +BR2_ROOTFS_POST_IMAGE_SCRIPT="board/nxp/common/ls/post-image.sh"
> > +BR2_ROOTFS_POST_SCRIPT_ARGS="$(LINUX_DIR) $(TOPDIR)
> $(UBOOT_DIR)"
> > +
> > +# busybox setting
> > +BR2_PACKAGE_BUSYBOX_SHOW_OTHERS=y
> > +
> > +# packages for rcw
> > +BR2_PACKAGE_HOST_QORIQ_RCW=y
> > +BR2_PACKAGE_HOST_QORIQ_RCW_BOOT_MODE="emmc"
> >
> +BR2_PACKAGE_HOST_QORIQ_RCW_BIN="ls1028ardb/R_SQPP_0x85bb/rcw_1
> 300_emmcboot.bin"
> > +
> > +#Display port firmware
> > +BR2_PACKAGE_QORIQ_CADENCE_DP_FIRMWARE=y
> > +
> > +#eudev support
> > +BR2_ROOTFS_DEVICE_CREATION_DYNAMIC_EUDEV=y
> >
> +BR2_ROOTFS_POST_BUILD_SCRIPT="board/nxp/ls1028ardb/post-cfg-udev.sh"
> > +
> > +# Arm-Trusted-Firmware
> > +BR2_TARGET_ARM_TRUSTED_FIRMWARE=y
> > +BR2_TARGET_ARM_TRUSTED_FIRMWARE_FIP=y
> > +BR2_TARGET_ARM_TRUSTED_FIRMWARE_UBOOT_AS_BL33=y
> >
> +BR2_TARGET_ARM_TRUSTED_FIRMWARE_UBOOT_BL33_IMAGE="u-boot-dt
> b.bin"
> > +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_GIT=y
> >
> +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_REPO_URL="https://eur
> 01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fsource.codeaurora.
> org%2Fexternal%2Fqoriq%2Fqoriq-components%2Fatf&data=02%7C01%7
> Cjerry.huang%40nxp.com%7Cae8709aebdf54eef25ed08d77792f39a%7C686ea1
> d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C637109345348800651&sdat
> a=QxY1g3x9g%2FVOObPfmMgqiX1KCF8jYUzYT33inYJYCyA%3D&reserved=
> 0"
> >
> +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_REPO_VERSION="LSDK-
> 19.09"
> > +BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="ls1028ardb"
> > +BR2_TARGET_ARM_TRUSTED_FIRMWARE_IMAGES="fip.bin bl2_emmc.pbl"
> > +BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_TARGETS="pbl"
> >
> +BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_DEPENDENCIES="h
> ost-qoriq-rcw"
> >
> +BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_VARIABLES="BOOT
> _MODE=emmc RCW=$(BINARIES_DIR)/rcw_1300_emmcboot.bin"
> > diff --git a/configs/nxp_ls1028ardb-64b-xspi_defconfig
> > b/configs/nxp_ls1028ardb-64b-xspi_defconfig
> > new file mode 100644
> > index 0000000000..66241c4c79
> > --- /dev/null
> > +++ b/configs/nxp_ls1028ardb-64b-xspi_defconfig
> > @@ -0,0 +1,85 @@
> > +# Architecture
> > +BR2_aarch64=y
> > +BR2_cortex_a72=y
> > +
> > +# Filesystem
> > +BR2_TARGET_ROOTFS_CPIO=y
> > +BR2_TARGET_ROOTFS_CPIO_GZIP=y
> > +BR2_TARGET_ROOTFS_CPIO_UIMAGE=y
> > +
> > +# Hostname and issue
> > +BR2_TARGET_GENERIC_HOSTNAME="LS1028ARDB"
> > +
> > +# toolchain
> > +BR2_TOOLCHAIN_BUILDROOT_GLIBC=y
> > +BR2_TOOLCHAIN_BUILDROOT_LIBC="glibc"
> > +
> > +# Linux headers same as kernel
> > +BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_19=y
> > +
> > +# bootloader
> > +BR2_TARGET_UBOOT=y
> > +BR2_TARGET_UBOOT_BOARDNAME="ls1028ardb_tfa"
> > +BR2_TARGET_UBOOT_CUSTOM_GIT=y
> >
> +BR2_TARGET_UBOOT_CUSTOM_REPO_URL="https://eur01.safelinks.protectio
> n.outlook.com/?url=https%3A%2F%2Fsource.codeaurora.org%2Fexternal%2Fqo
> riq%2Fqoriq-components%2Fu-boot&data=02%7C01%7Cjerry.huang%40nx
> p.com%7Cae8709aebdf54eef25ed08d77792f39a%7C686ea1d3bc2b4c6fa92cd9
> 9c5c301635%7C0%7C0%7C637109345348800651&sdata=kFn3nsvOHgCCT
> JYKYMoU9rRkGsFR77TYGzbvOEezXIg%3D&reserved=0"
> > +BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="LSDK-19.09"
> > +BR2_TARGET_UBOOT_NEEDS_DTC=y
> > +BR2_TARGET_UBOOT_FORMAT_BIN=n
> > +BR2_TARGET_UBOOT_FORMAT_CUSTOM=y
> > +BR2_TARGET_UBOOT_FORMAT_CUSTOM_NAME="u-boot-dtb.bin"
> > +BR2_TARGET_UBOOT_ENVIMAGE=y
> >
> +BR2_TARGET_UBOOT_ENVIMAGE_SOURCE="board/nxp/ls1028ardb/u-boot-e
> nvironment-xspi.txt"
> > +BR2_TARGET_UBOOT_ENVIMAGE_SIZE="0x2000"
> > +
> > +# Kernel
> > +BR2_LINUX_KERNEL=y
> > +BR2_LINUX_KERNEL_CUSTOM_GIT=y
> >
> +BR2_LINUX_KERNEL_CUSTOM_REPO_URL="https://eur01.safelinks.protection
> .outlook.com/?url=https%3A%2F%2Fsource.codeaurora.org%2Fexternal%2Fqor
> iq%2Fqoriq-components%2Flinux&data=02%7C01%7Cjerry.huang%40nxp.
> com%7Cae8709aebdf54eef25ed08d77792f39a%7C686ea1d3bc2b4c6fa92cd99c
> 5c301635%7C0%7C0%7C637109345348810637&sdata=Akdyy0hEI%2Fiqw
> y6oPyt6OLrLAea1JpikT2r8BI9Yvz8%3D&reserved=0"
> > +BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="LSDK-19.09-V4.19"
> > +BR2_LINUX_KERNEL_USE_ARCH_DEFAULT_CONFIG=y
> >
> +BR2_LINUX_KERNEL_CONFIG_FRAGMENT_FILES="$(LINUX_DIR)/arch/arm64
> /configs/lsdk.config"
> > +BR2_LINUX_KERNEL_DTS_SUPPORT=y
> > +BR2_LINUX_KERNEL_INTREE_DTS_NAME="freescale/fsl-ls1028a-rdb"
> > +BR2_LINUX_KERNEL_IMAGE_TARGET_CUSTOM=y
> > +BR2_LINUX_KERNEL_IMAGE_TARGET_NAME="Image.gz"
> > +
> > +# Serial port config
> > +BR2_TARGET_GENERIC_GETTY=y
> > +BR2_TARGET_GENERIC_GETTY_PORT="ttyS0"
> > +
> > +# required tools to create the microSD image
> > +BR2_PACKAGE_HOST_DOSFSTOOLS=y BR2_PACKAGE_HOST_GENIMAGE=y
> > +BR2_PACKAGE_HOST_MTOOLS=y
> >
> +BR2_ROOTFS_POST_IMAGE_SCRIPT="board/nxp/common/ls/post-image-spi.s
> h"
> > +BR2_ROOTFS_POST_SCRIPT_ARGS="$(LINUX_DIR) $(TOPDIR)
> $(UBOOT_DIR)"
> > +
> > +# busybox setting
> >
> +BR2_PACKAGE_BUSYBOX_CONFIG_FRAGMENT_FILES="board/nxp/common/ls
> /busybox.config"
> > +BR2_PACKAGE_BUSYBOX_SHOW_OTHERS=y
> > +
> > +# packages for rcw
> > +BR2_PACKAGE_HOST_QORIQ_RCW=y
> > +BR2_PACKAGE_HOST_QORIQ_RCW_BOOT_MODE="flexspi_nor"
> >
> +BR2_PACKAGE_HOST_QORIQ_RCW_BIN="ls1028ardb/R_SQPP_0x85bb/rcw_1
> 500_gpu600.bin"
> > +
> > +#Display port firmware
> > +BR2_PACKAGE_QORIQ_CADENCE_DP_FIRMWARE=y
> > +
> > +#eudev support
> > +BR2_ROOTFS_DEVICE_CREATION_DYNAMIC_EUDEV=y
> >
> +BR2_ROOTFS_POST_BUILD_SCRIPT="board/nxp/ls1028ardb/post-cfg-udev.sh"
> > +
> > +# Arm-Trusted-Firmware
> > +BR2_TARGET_ARM_TRUSTED_FIRMWARE=y
> > +BR2_TARGET_ARM_TRUSTED_FIRMWARE_FIP=y
> > +BR2_TARGET_ARM_TRUSTED_FIRMWARE_UBOOT_AS_BL33=y
> >
> +BR2_TARGET_ARM_TRUSTED_FIRMWARE_UBOOT_BL33_IMAGE="u-boot-dt
> b.bin"
> > +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_GIT=y
> >
> +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_REPO_URL="https://eur
> 01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fsource.codeaurora.
> org%2Fexternal%2Fqoriq%2Fqoriq-components%2Fatf&data=02%7C01%7
> Cjerry.huang%40nxp.com%7Cae8709aebdf54eef25ed08d77792f39a%7C686ea1
> d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C637109345348810637&sdat
> a=9ssQTjqQMNf7FgKISQPKHB0ywJkUCcorbBjCIVodYkE%3D&reserved=0"
> >
> +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_REPO_VERSION="LSDK-
> 19.09"
> > +BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="ls1028ardb"
> > +BR2_TARGET_ARM_TRUSTED_FIRMWARE_IMAGES="fip.bin
> bl2_flexspi_nor.pbl"
> > +BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_TARGETS="pbl"
> >
> +BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_DEPENDENCIES="h
> ost-qoriq-rcw"
> >
> +BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_VARIABLES="BOOT
> _MODE=flexspi_nor RCW=$(BINARIES_DIR)/rcw_1500_gpu600.bin"
> > diff --git a/configs/nxp_ls1028ardb-64b_defconfig
> > b/configs/nxp_ls1028ardb-64b_defconfig
> > new file mode 100644
> > index 0000000000..fdb251058f
> > --- /dev/null
> > +++ b/configs/nxp_ls1028ardb-64b_defconfig
> > @@ -0,0 +1,85 @@
> > +# Architecture
> > +BR2_aarch64=y
> > +BR2_cortex_a72=y
> > +
> > +# Filesystem
> > +BR2_TARGET_ROOTFS_EXT2=y
> > +BR2_TARGET_ROOTFS_EXT2_4=y
> > +
> > +# Hostname and issue
> > +BR2_TARGET_GENERIC_HOSTNAME="LS1028ARDB"
> > +
> > +# toolchain
> > +BR2_TOOLCHAIN_BUILDROOT_GLIBC=y
> > +BR2_TOOLCHAIN_BUILDROOT_LIBC="glibc"
> > +
> > +# Linux headers same as kernel
> > +BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_19=y
> > +
> > +# bootloader
> > +BR2_TARGET_UBOOT=y
> > +BR2_TARGET_UBOOT_BOARDNAME="ls1028ardb_tfa"
> > +BR2_TARGET_UBOOT_CUSTOM_GIT=y
> >
> +BR2_TARGET_UBOOT_CUSTOM_REPO_URL="https://eur01.safelinks.protectio
> n.outlook.com/?url=https%3A%2F%2Fsource.codeaurora.org%2Fexternal%2Fqo
> riq%2Fqoriq-components%2Fu-boot&data=02%7C01%7Cjerry.huang%40nx
> p.com%7Cae8709aebdf54eef25ed08d77792f39a%7C686ea1d3bc2b4c6fa92cd9
> 9c5c301635%7C0%7C0%7C637109345348810637&sdata=XB0okA3zSQFVF
> 8QmKrSgy%2BXnZ5hcqvfRo%2FznvzodgSs%3D&reserved=0"
> > +BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="LSDK-19.09"
> > +BR2_TARGET_UBOOT_NEEDS_DTC=y
> > +BR2_TARGET_UBOOT_FORMAT_BIN=n
> > +BR2_TARGET_UBOOT_FORMAT_CUSTOM=y
> > +BR2_TARGET_UBOOT_FORMAT_CUSTOM_NAME="u-boot-dtb.bin"
> > +BR2_PACKAGE_UBOOT_TOOLS_MKIMAGE=y
> > +BR2_TARGET_UBOOT_ENVIMAGE=y
> >
> +BR2_TARGET_UBOOT_ENVIMAGE_SOURCE="board/nxp/ls1028ardb/u-boot-e
> nvironment-sd.txt"
> > +BR2_TARGET_UBOOT_ENVIMAGE_SIZE="0x2000"
> > +
> > +# Kernel
> > +BR2_LINUX_KERNEL=y
> > +BR2_LINUX_KERNEL_CUSTOM_GIT=y
> >
> +BR2_LINUX_KERNEL_CUSTOM_REPO_URL="https://eur01.safelinks.protection
> .outlook.com/?url=https%3A%2F%2Fsource.codeaurora.org%2Fexternal%2Fqor
> iq%2Fqoriq-components%2Flinux&data=02%7C01%7Cjerry.huang%40nxp.
> com%7Cae8709aebdf54eef25ed08d77792f39a%7C686ea1d3bc2b4c6fa92cd99c
> 5c301635%7C0%7C0%7C637109345348810637&sdata=Akdyy0hEI%2Fiqw
> y6oPyt6OLrLAea1JpikT2r8BI9Yvz8%3D&reserved=0"
> > +BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="LSDK-19.09-V4.19"
> > +BR2_LINUX_KERNEL_USE_ARCH_DEFAULT_CONFIG=y
> >
> +BR2_LINUX_KERNEL_CONFIG_FRAGMENT_FILES="$(LINUX_DIR)/arch/arm64
> /configs/lsdk.config"
> > +BR2_LINUX_KERNEL_DTS_SUPPORT=y
> > +BR2_LINUX_KERNEL_INTREE_DTS_NAME="freescale/fsl-ls1028a-rdb"
> > +BR2_LINUX_KERNEL_IMAGE_TARGET_CUSTOM=y
> > +BR2_LINUX_KERNEL_IMAGE_TARGET_NAME="Image"
> > +
> > +# Serial port config
> > +BR2_TARGET_GENERIC_GETTY=y
> > +BR2_TARGET_GENERIC_GETTY_PORT="ttyS0"
> > +
> > +# required tools to create the microSD image
> > +BR2_PACKAGE_HOST_DOSFSTOOLS=y BR2_PACKAGE_HOST_GENIMAGE=y
> > +BR2_PACKAGE_HOST_MTOOLS=y
> > +BR2_ROOTFS_POST_IMAGE_SCRIPT="board/nxp/common/ls/post-image.sh"
> > +BR2_ROOTFS_POST_SCRIPT_ARGS="$(LINUX_DIR) $(TOPDIR)
> $(UBOOT_DIR)"
> > +
> > +# busybox setting
> >
> +BR2_PACKAGE_BUSYBOX_CONFIG_FRAGMENT_FILES="board/nxp/common/ls
> /busybox.config"
> > +BR2_PACKAGE_BUSYBOX_SHOW_OTHERS=y
> > +
> > +# packages for rcw
> > +BR2_PACKAGE_HOST_QORIQ_RCW=y
> > +BR2_PACKAGE_HOST_QORIQ_RCW_BOOT_MODE="sd"
> >
> +BR2_PACKAGE_HOST_QORIQ_RCW_BIN="ls1028ardb/R_SQPP_0x85bb/rcw_1
> 300_sdboot.bin"
> > +
> > +#Display port firmware
> > +BR2_PACKAGE_QORIQ_CADENCE_DP_FIRMWARE=y
> > +
> > +#eudev support
> > +BR2_ROOTFS_DEVICE_CREATION_DYNAMIC_EUDEV=y
> >
> +BR2_ROOTFS_POST_BUILD_SCRIPT="board/nxp/ls1028ardb/post-cfg-udev.sh"
> > +
> > +# Arm-Trusted-Firmware
> > +BR2_TARGET_ARM_TRUSTED_FIRMWARE=y
> > +BR2_TARGET_ARM_TRUSTED_FIRMWARE_FIP=y
> > +BR2_TARGET_ARM_TRUSTED_FIRMWARE_UBOOT_AS_BL33=y
> >
> +BR2_TARGET_ARM_TRUSTED_FIRMWARE_UBOOT_BL33_IMAGE="u-boot-dt
> b.bin"
> > +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_GIT=y
> >
> +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_REPO_URL="https://eur
> 01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fsource.codeaurora.
> org%2Fexternal%2Fqoriq%2Fqoriq-components%2Fatf&data=02%7C01%7
> Cjerry.huang%40nxp.com%7Cae8709aebdf54eef25ed08d77792f39a%7C686ea1
> d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C637109345348810637&sdat
> a=9ssQTjqQMNf7FgKISQPKHB0ywJkUCcorbBjCIVodYkE%3D&reserved=0"
> >
> +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_REPO_VERSION="LSDK-
> 19.09"
> > +BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="ls1028ardb"
> > +BR2_TARGET_ARM_TRUSTED_FIRMWARE_IMAGES="fip.bin bl2_sd.pbl"
> > +BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_TARGETS="pbl"
> >
> +BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_DEPENDENCIES="h
> ost-qoriq-rcw"
> >
> +BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_VARIABLES="BOOT
> _MODE=sd RCW=$(BINARIES_DIR)/rcw_1300_sdboot.bin"
> > --
> > 2.17.1
> >
> > _______________________________________________
> > buildroot mailing list
> > buildroot at busybox.net
> > https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Flists
> > .busybox.net%2Fmailman%2Flistinfo%2Fbuildroot&data=02%7C01%7Cje
> rry
> > .huang%40nxp.com%7Cae8709aebdf54eef25ed08d77792f39a%7C686ea1d3b
> c2b4c6f
> >
> a92cd99c5c301635%7C0%7C0%7C637109345348810637&sdata=0eld04G
> 7Qo%2F0
> > fDASkUbxYjsWLfeUCgf0bH2ee3O3JQQ%3D&reserved=0
>
> Thanks,
> -Vladimir
More information about the buildroot
mailing list