[Buildroot] [PATCH v4 1/1] configs/arcturus_ucls1012a: new defconfig
Oleksandr G Zhadan
oleks at arcturusnetworks.com
Mon Jul 17 13:26:08 UTC 2017
Hello Thomas,
Thanks for applying to master our uCP1020 changes.
Can you look closer to this uCLS1012A new version of the patch ?
Kind Regards,
Oleks
On 07/06/2017 05:13 PM, Oleksandr Zhadan wrote:
> The uCLS1012A-SOM product family (ucls1012a) is an Arcturus Networks Inc.
> 64bit ARM Cortex-A53 class System on Module powered by a NXP QorIQ LS1012A
> Low Power Communication Processor. This 314 pin MXM3.0/SMARC module card
> contains DDR3, QSPI NOR Flash, eMMC NAND Flash, optional Audio CODEC and is
> available with 1 or 2 Gig-Ethernet PHYs.
>
> Signed-off-by: Oleksandr Zhadan <oleks at arcturusnetworks.com>
> Signed-off-by: Michael Durrant <mdurrant at arcturusnetworks.com>
> ---
>
> Changes v3-> v4
> - post-image.sh cleaned
> - post-build.sh removed
> - toolchain changed to the internal
> - added version in the custom tarball names
> - added developers names into DEVELOPER file
>
> Changes v2 -> v3:
> - commit title is changed (from "Arcturus uCLS1012A-SOM support")
> - new updates in readme.txt
> - ls1012a network firmware moved into kernel
> - do not remove any intermediate files
> - fix relative patches inside ucls1012a.its
>
> Changes v1 -> v2:
> - updated readme.txt
> - fixed post-image.sh (Do not have to remove Image and *.dtb files)
> ---
>
> Signed-off-by: Oleksandr Zhadan <oleks at arcturusnetworks.com>
> ---
> DEVELOPERS | 8 +++
> board/arcturus/aarch64-ucls1012a/post-image.sh | 7 ++
> board/arcturus/aarch64-ucls1012a/readme.txt | 74 ++++++++++++++++++++++
> .../rootfs_overlay/etc/init.d/S09modload | 14 ++++
> board/arcturus/aarch64-ucls1012a/ucls1012a.its | 50 +++++++++++++++
> configs/arcturus_ucls1012a_defconfig | 22 +++++++
> 6 files changed, 175 insertions(+)
> create mode 100755 board/arcturus/aarch64-ucls1012a/post-image.sh
> create mode 100644 board/arcturus/aarch64-ucls1012a/readme.txt
> create mode 100755 board/arcturus/aarch64-ucls1012a/rootfs_overlay/etc/init.d/S09modload
> create mode 100644 board/arcturus/aarch64-ucls1012a/ucls1012a.its
> create mode 100644 configs/arcturus_ucls1012a_defconfig
>
> diff --git a/DEVELOPERS b/DEVELOPERS
> index c409f2822..623a05b79 100644
> --- a/DEVELOPERS
> +++ b/DEVELOPERS
> @@ -1219,6 +1219,10 @@ F: package/tinyxml/
> N: Maxime Ripard <maxime.ripard at free-electrons.com>
> F: package/kmsxx/
>
> +N: Michael Durrant <mdurrant at arcturusnetworks.com>
> +F: board/arcturus/
> +F: configs/arcturus_*
> +
> N: Michael Rommel <rommel at layer-7.net>
> F: package/aiccu/
> F: package/knock/
> @@ -1264,6 +1268,10 @@ F: package/trousers/
> N: Olaf Rempel <razzor at kopf-tisch.de>
> F: package/ctorrent/
>
> +N: Oleksandr Zhadan <oleks at arcturusnetworks.com>
> +F: board/arcturus/
> +F: configs/arcturus_*
> +
> N: Oli Vogt <oli.vogt.pub01 at gmail.com>
> F: package/python-django/
> F: package/python-flup/
> diff --git a/board/arcturus/aarch64-ucls1012a/post-image.sh b/board/arcturus/aarch64-ucls1012a/post-image.sh
> new file mode 100755
> index 000000000..5280fc245
> --- /dev/null
> +++ b/board/arcturus/aarch64-ucls1012a/post-image.sh
> @@ -0,0 +1,7 @@
> +#!/bin/sh
> +
> +cp -f board/arcturus/aarch64-ucls1012a/ucls1012a.its ${BINARIES_DIR}/
> +MKIMAGE=${HOST_DIR}/usr/bin/mkimage
> +MKIMAGE_IN=${BINARIES_DIR}/ucls1012a.its
> +MKIMAGE_OUT=${BINARIES_DIR}/part0-000000.itb
> +${MKIMAGE} -f ${MKIMAGE_IN} ${MKIMAGE_OUT}
> diff --git a/board/arcturus/aarch64-ucls1012a/readme.txt b/board/arcturus/aarch64-ucls1012a/readme.txt
> new file mode 100644
> index 000000000..61fe3c55a
> --- /dev/null
> +++ b/board/arcturus/aarch64-ucls1012a/readme.txt
> @@ -0,0 +1,74 @@
> +Arcturus uCLS1012A SoM
> +======================
> +
> +This tutorial describes how to use the predefined Buildroot
> +configuration for the Arcturus uCLS101A SoM platform.
> +
> +Additional information about the uCLS1012A System on Module can be found at
> +https://www.arcturusnetworks.com/products/ucls1012a
> +and product support for registered users at
> +https://www.arcturusnetworks.com/support
> +
> +Building
> +--------
> +
> +Return to the top directory <buildrootdir> and execute the following commands.
> +
> + make arcturus_ucls1012a_defconfig
> + make
> +
> +Result of the build
> +-------------------
> +
> +After building, you should obtain this tree:
> +
> + output/images/
> + +-- arc-ucls1012a.dtb
> + +-- Image
> + +-- part0-000000.itb
> + +-- rootfs.cpio
> + +-- rootfs.cpio.gz
> + +-- rootfs.tar
> + +-- u-boot.bin
> + +-- ucls1012a.its
> +
> +Flashing
> +--------
> +
> +You'll need to program the image created by buildroot into the SPI NOR flash.
> +
> +1. Reboot your module and via the serial console press <escape> to enter the B$
> +u-boot shell.
> + From the shell you will need to update four environment variables replacing the
> + IPv4 IP Address with ones that will work with your network and tftp server.
> +
> + B$ setenv ipaddr 192.168.1.81
> + B$ setenv serverip 192.168.1.80
> + B$ setenv gatewayip 192.168.1.1
> + B$ setenv netmask 255.255.255.0
> + B$ saveenv
> +
> +2. Enable tftp server to serve the <buildrootdir>/output/images/ folder.
> +
> +3. Program the new U-Boot binary (optional)
> + If you don't feel confident upgrading your bootloader then don't do it,
> + it's unnecessary most of the time.
> +
> + B$ tftp u-boot.bin
> + B$ run program_uboot
> +
> +4. Program the ITB image (includes Kernel, DTB and Ramdisk)
> +
> + B$ tftp part0-000000.itb
> + B$ run program0
> +
> +5. Booting your new system
> +
> + Reboot your system by reset command
> + B$ reset
> +
> + or
> +
> + B$ run bootcmd
> +
> +Good Luck !
> diff --git a/board/arcturus/aarch64-ucls1012a/rootfs_overlay/etc/init.d/S09modload b/board/arcturus/aarch64-ucls1012a/rootfs_overlay/etc/init.d/S09modload
> new file mode 100755
> index 000000000..c87ffda14
> --- /dev/null
> +++ b/board/arcturus/aarch64-ucls1012a/rootfs_overlay/etc/init.d/S09modload
> @@ -0,0 +1,14 @@
> +#!/bin/sh
> +#
> +case "$1" in
> + start)
> + modprobe pfe
> + ;;
> + stop)
> + ;;
> + restart|reload)
> + ;;
> + *)
> + echo "Usage: $0 {start|stop|restart}"
> + exit 1
> +esac
> diff --git a/board/arcturus/aarch64-ucls1012a/ucls1012a.its b/board/arcturus/aarch64-ucls1012a/ucls1012a.its
> new file mode 100644
> index 000000000..f19080d31
> --- /dev/null
> +++ b/board/arcturus/aarch64-ucls1012a/ucls1012a.its
> @@ -0,0 +1,50 @@
> +/*
> + * Copyright (C) 2017, Arcturus Networks Inc.
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +/ {
> + description = "Image file for the Arcturus uCLS1012A Linux Kernel";
> + #address-cells = <1>;
> + images {
> + kernel {
> + description = "Linux kernel";
> + data = /incbin/("Image");
> + type = "kernel";
> + arch = "arm64";
> + os = "linux";
> + compression = "none";
> + load = <0x80080000>;
> + entry = <0x80080000>;
> + };
> + fdt {
> + description = "Flattened Device Tree Blob";
> + data = /incbin/("arc-ucls1012a.dtb");
> + type = "flat_dt";
> + arch = "arm64";
> + compression = "none";
> + load = <0x90000000>;
> + };
> + ramdisk {
> + description = "Ramdisk";
> + data = /incbin/("rootfs.cpio.gz");
> + type = "ramdisk";
> + arch = "arm64";
> + os = "linux";
> + compression = "gzip";
> + };
> + };
> + configurations {
> + default = "config";
> + config {
> + kernel = "kernel";
> + fdt = "fdt";
> + ramdisk = "ramdisk";
> + };
> + };
> +};
> diff --git a/configs/arcturus_ucls1012a_defconfig b/configs/arcturus_ucls1012a_defconfig
> new file mode 100644
> index 000000000..325b0ceab
> --- /dev/null
> +++ b/configs/arcturus_ucls1012a_defconfig
> @@ -0,0 +1,22 @@
> +BR2_aarch64=y
> +BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
> +BR2_TARGET_GENERIC_HOSTNAME="ucls1012a"
> +BR2_TARGET_GENERIC_ISSUE="Welcome to uCLS1012A-SOM"
> +BR2_SYSTEM_DHCP="eth0"
> +BR2_ROOTFS_OVERLAY="board/arcturus/aarch64-ucls1012a/rootfs_overlay"
> +BR2_ROOTFS_POST_IMAGE_SCRIPT="board/arcturus/aarch64-ucls1012a/post-image.sh"
> +BR2_LINUX_KERNEL=y
> +BR2_LINUX_KERNEL_CUSTOM_TARBALL=y
> +BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION="https://www.arcturusnetworks.com/OSS/kernel-ucls1012a-170706-13.tar.gz"
> +BR2_LINUX_KERNEL_DEFCONFIG="ucls1012a"
> +BR2_LINUX_KERNEL_DTS_SUPPORT=y
> +BR2_LINUX_KERNEL_INTREE_DTS_NAME="arcturus/arc-ucls1012a"
> +BR2_TARGET_ROOTFS_CPIO=y
> +BR2_TARGET_ROOTFS_CPIO_GZIP=y
> +BR2_TARGET_UBOOT=y
> +BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y
> +BR2_TARGET_UBOOT_CUSTOM_TARBALL=y
> +BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION="https://www.arcturusnetworks.com/OSS/u-boot-ucls1012a-170706-13.tar.gz"
> +BR2_TARGET_UBOOT_BOARD_DEFCONFIG="UCLS1012A_QSPI"
> +BR2_PACKAGE_HOST_UBOOT_TOOLS=y
> +BR2_PACKAGE_HOST_UBOOT_TOOLS_FIT_SUPPORT=y
More information about the buildroot
mailing list