[Buildroot] [PATCH 1/1] board: add support for Xilinx zc706

jordi montage jordi.montagne66 at gmail.com
Fri Mar 6 18:34:40 UTC 2015


up


On Sun, Mar 1, 2015 at 3:48 PM, Jordi Montagne
<jordi.montagne66 at gmail.com> wrote:
> This is a Xilinx Zynq (xc7z045) development board, based on Xilinx Zynq
> (xc7z045).
>
> This support is based on Avnet Zedboard defconfig/readme.
>
> Signed-off-by: Jordi Montagne <jordi.montagne66 at gmail.com>
> ---
>  board/xilinx/zc706/readme.txt | 75 +++++++++++++++++++++++++++++++++++++++++++
>  configs/zc706_defconfig       | 26 +++++++++++++++
>  2 files changed, 101 insertions(+)
>  create mode 100644 board/xilinx/zc706/readme.txt
>  create mode 100644 configs/zc706_defconfig
>
> diff --git a/board/xilinx/zc706/readme.txt b/board/xilinx/zc706/readme.txt
> new file mode 100644
> index 0000000..00e45b3
> --- /dev/null
> +++ b/board/xilinx/zc706/readme.txt
> @@ -0,0 +1,75 @@
> +This is the buildroot board support for the Xilinx ZC706. The ZC706 is
> +a development board based on the Xilinx Zynq-7000 based All-Programmable
> +System-On-Chip.
> +
> +ZC706 information including schematics, reference designs, and manuals are
> +available from
> +http://www.xilinx.com/products/boards-and-kits/ek-z7-zc706-g.html.
> +
> +The U-Boot firmware for the Xilinx Zynq All Programmable SoC depends
> +on some propietary code. This dependency consists of a pair of
> +files are available from the Xilinx SDK installation.
> +
> +You will need these files from Xilinx SDK installation to generate
> +the U-Boot firmware:
> +       ps7_init.c
> +       ps7_init.h
> +
> +Buildroot will create the following files and place them in the
> +<output>/images directory.
> +       zynq-zc706.dtb
> +       rootfs.cpio.uboot
> +       uImage
> +       u-boot.img
> +       boot.bin
> +
> +
> +uboot.bin  -- U-Boot SPL w/ Xilinx boot.bin wrapper
> +---------------------------------------------------
> +
> +Due to licensing issues, the files ps7_init.c/h are not able to be
> +distributed with the U-Boot source code.  These files are required to make a
> +boot.bin file.
> +
> +If you already have the Xilinx tools installed, the following sequence will
> +unpack, patch and build the rfs, kernel, uboot, and uboot-spl.
> +
> +make zc706_defconfig
> +make uboot-patch
> +cp ${XILINX_SDK}/hwplatform_templates/ZC706_hw_platform/ps7_init.{c,h} \
> +output/build/uboot-xilinx-v2014.1/board/xilinx/zynq/
> +
> +Where ${XILINX_SDK_LIB} is ${XILINX}/SDK/${VERSION}/data/embeddedsw/lib.
> +
> +After copying these files into the U-Boot source tree, you can
> +continue the build with:
> +
> +make
> +
> +*Notice*
> +While the build will successfully complete without the ps7_init.*
> +files,  the uboot.bin file generated by this configuration will not
> +function properly on the ZC706.  Therefore, it is imperative that
> +the ps7_init.* files be copied into the U-Boot source tree any time
> +the clean, or uboot-dirclean targets are made.
> +
> +
> +Resulting system
> +----------------
> +A FAT32 partition should be created at the beggining of the SD Card
> +and the following files should be installed:
> +       /boot.bin
> +       /devicetree.dtb
> +       /uImage
> +       /uramdisk.image.gz
> +       /u-boot.img
> +
> +
> +All needed files can be taken from output/images/
> +
> +boot.bin, uImage and u-boot.img are direct copies of the same files
> +available on output/images/
> +
> +devicetree.dtb is just zynq-zc706.dtb renamed.
> +
> +uramdisk.image.gz is rootfs.cpio.uboot renamed
> diff --git a/configs/zc706_defconfig b/configs/zc706_defconfig
> new file mode 100644
> index 0000000..bb0aadc
> --- /dev/null
> +++ b/configs/zc706_defconfig
> @@ -0,0 +1,26 @@
> +BR2_arm=y
> +BR2_cortex_a9=y
> +BR2_ARM_ENABLE_NEON=y
> +BR2_KERNEL_HEADERS_VERSION=y
> +BR2_DEFAULT_KERNEL_VERSION="3.8"
> +BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_8=y
> +BR2_TARGET_GENERIC_GETTY_PORT="ttyPS0"
> +BR2_LINUX_KERNEL=y
> +BR2_LINUX_KERNEL_CUSTOM_GIT=y
> +BR2_LINUX_KERNEL_CUSTOM_REPO_URL="git://github.com/Xilinx/linux-xlnx.git"
> +BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="xilinx-v2014.2.01"
> +BR2_LINUX_KERNEL_DEFCONFIG="xilinx_zynq"
> +BR2_LINUX_KERNEL_UIMAGE_LOADADDR="0x8000"
> +BR2_LINUX_KERNEL_DTS_SUPPORT=y
> +BR2_LINUX_KERNEL_INTREE_DTS_NAME="zynq-zc706"
> +BR2_TARGET_ROOTFS_CPIO=y
> +BR2_TARGET_ROOTFS_CPIO_GZIP=y
> +BR2_TARGET_ROOTFS_CPIO_UIMAGE=y
> +BR2_TARGET_UBOOT=y
> +BR2_TARGET_UBOOT_BOARDNAME="zynq_zc70x"
> +BR2_TARGET_UBOOT_CUSTOM_GIT=y
> +BR2_TARGET_UBOOT_CUSTOM_REPO_URL="git://github.com/Xilinx/u-boot-xlnx.git"
> +BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="xilinx-v2014.1"
> +BR2_TARGET_UBOOT_FORMAT_IMG=y
> +BR2_TARGET_UBOOT_SPL=y
> +BR2_TARGET_UBOOT_SPL_NAME="boot.bin"
> --
> 2.0.5
>


More information about the buildroot mailing list