[Buildroot] bootm - "Starting kernel"
Jörg Krause
joerg.krause at embedded.rocks
Wed Aug 12 12:00:35 UTC 2015
Hi Tommy Lee,
On Di, 2015-08-11 at 16:27 -0700, Lee, Tommy wrote:
> Hi Buildroot mailing list,
>
> My host is Ubuntu-14.04 LTS. My Buildroot release is 2015.05. I have
> made the former meet the latter’s requirements. My target is Marvell
> ARMADA A385 (ARM-Cortex-A9) DB-88F6820-GP. This board is bootable
> using the U-Boot-1.73 and the USB which are given by Marvell.
>
> I used Buildroot-2015.05 and built the uImage and rootfs.cpio.uboot
> with no problems. I enabled the TFTP server on my host.
>
> On my target, the execution of the following commands, listed below,
> ended up with “Starting kernel”, no display of kernel booting
> messages. The attached is the .config file I created this the make
> process.
>
> I am resolving this issue now. Your experience sharing is extremely
> grateful.
>
> Tommy
>
> Marvell>> tftp 02000000 10.28.1.20:uImage
> Using egiga0 device
> TFTP from server 10.28.1.20; our IP address is 10.28.1.47
> Filename 'uImage'.
> Load address: 0x2000000
> Loading:
> #################################################################
>
> #################################################################
>
> #################################################################
> ##############
> 1.6 MiB/s
> done
> Bytes transferred = 1066696 (1046c8 hex)
> Marvell>> tftp 02200000 10.28.1.20:rootfs.cpio.uboot
> Using egiga0 device
> TFTP from server 10.28.1.20; our IP address is 10.28.1.47
> Filename 'rootfs.cpio.uboot'.
> Load address: 0x2200000
> Loading:
> #################################################################
>
> #################################################################
>
> #################################################################
>
> #################################################################
>
> #################################################################
>
> #################################################################
>
> #################################################################
>
> #################################################################
>
> #################################################################
>
> #################################################################
>
> #################################################################
>
> #################################################################
>
> #################################################################
>
> #################################################################
> ######################
> 1.7 MiB/s
> done
> Bytes transferred = 4769344 (48c640 hex)
> Marvell>> bootm 02000000 02200000
> ## Booting kernel from Legacy Image at 02000000 ...
> Image Name: Linux-4.0.4
> Created: 2015-08-11 0:21:58 UTC
> Image Type: ARM Linux Kernel Image (uncompressed)
> Data Size: 1066632 Bytes = 1 MiB
> Load Address: 02000000
> Entry Point: 02000000
> Verifying Checksum ... OK
> ## Loading init Ramdisk from Legacy Image at 02200000 ...
> Image Name:
> Created: 2015-08-11 15:25:49 UTC
> Image Type: ARM Linux RAMDisk Image (uncompressed)
> Data Size: 4769280 Bytes = 4.5 MiB
> Load Address: 00000000
> Entry Point: 00000000
> Verifying Checksum ... OK
> XIP Kernel Image ... OK
> OK
>
> Starting kernel ...
I guess for a misconfigured console... TI has very helpful
documentation about using U-Boot and Linux [1].
Best regards
Jörg Krause
[1] http://processors.wiki.ti.com/index.php/Kernel_-_Common_Problems_Bo
oting_Linux#Problem_.231_
-_No_more_output_is_seen_on_the_console_after_.22Starting_Kernel....22
More information about the buildroot
mailing list