[Buildroot] [PATCH] Adding Microblaze support to Buildroot
Spenser Gilliland
spenser309 at gmail.com
Mon Feb 13 19:51:46 UTC 2012
It should be copied by the LINUX_COPY_DTS routine in linux/linux.mk
that was added by the patch. Is there a line "Cannot copy dts file!"
in the build output?
Spenser
On Mon, Feb 13, 2012 at 1:48 PM, Alvaro Gamez <alvaro.gamez at hazent.com> wrote:
> No, it isn't there.
>
> But the refered board/avnet/LX9MicroBoard/lx9_mmu.dts in the config files
> does exist. I guess something should have copied it there but failed
> somehow?
>
>
> 2012/2/13 Spenser Gilliland <spenser309 at gmail.com>
>>
>> Is there a file named lx9_mmu.dts file in
>> output/build/linux-x.x.x/arch/microblaze/boot/dts/ ?
>>
>> Spenser
>>
>> On Mon, Feb 13, 2012 at 1:40 PM, Alvaro Gamez <alvaro.gamez at hazent.com>
>> wrote:
>> > I checked and this is the content of the config file:
>> >
>> >
>> > BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="$(TOPDIR)/board/avnet/LX9MicroBoard/lx9_mmu_defconfig"
>> >
>> > BR2_LINUX_KERNEL_DTS_FILE="$(TOPDIR)/board/avnet/LX9MicroBoard/lx9_mmu.dts"
>> > BR2_LINUX_KERNEL_IMAGE_TARGET_NAME="simpleImage.lx9_mmu"
>> >
>> > so I think there has to be some other thing I'm not aware of.
>> >
>> >
>> > 2012/2/13 Spenser Gilliland <spenser309 at gmail.com>
>> >>
>> >> This means that the dts was not copied into the
>> >> arch/microblaze/boot/dts
>> >> dir or you are not building the correct target.
>> >>
>> >> You need to verify that the BR2_LINUX_KERNEL_DTS_FILE is set to a real
>> >> file and that BR2_LINUX_KERNEL_IMAGE_TARGET_NAME is set to
>> >> simpleImage.$(filename-wo-extension).
>> >>
>> >> IE. if BR2_LINUX_KERNEL_DTS_FILE = /path/to/dts/xupv5.dts then
>> >> BR2_LINUX_KERNEL_IMAGE_TARGET=simpleImage.xupv5.
>> >>
>> >> Spenser
>> >>
>> >> On Feb 13, 2012 1:14 PM, "Alvaro Gamez" <alvaro.gamez at hazent.com>
>> >> wrote:
>> >>>
>> >>> Ok, now that I have a little time I'm trying to make it work.
>> >>>
>> >>> I haven't had any problem yet with GCC tune. However, I'm getting the
>> >>> following error while trying to build the kernel
>> >>>
>> >>> make[2]: *** No rule to make target
>> >>> `arch/microblaze/boot/lx9_mmu.dtb',
>> >>> needed by `arch/microblaze/boot/system.dtb'. Stop.
>> >>>
>> >>> Any idea?
>> >>>
>> >>> Regards
>> >>>
>> >>>
>> >>> 2012/2/13 Alvaro Gamez <alvaro.gamez at hazent.com>
>> >>>>
>> >>>> I am yet to test it. I just found yersterday that buildroot exists :)
>> >>>>
>> >>>>
>> >>>> 2012/2/13 Spenser Gilliland <spenser309 at gmail.com>
>> >>>>>
>> >>>>> Alvaro,
>> >>>>>
>> >>>>> Did you have issues with the GCC tune? I had to remove that line
>> >>>>> from
>> >>>>> the original patch.
>> >>>>>
>> >>>>> Spenser
>> >>>>>
>> >>>>> On Sun, Feb 12, 2012 at 5:07 PM, Alvaro Gamez
>> >>>>> <alvaro.gamez at hazent.com>
>> >>>>> wrote:
>> >>>>> > Hi
>> >>>>> >
>> >>>>> > I am also interested on Microblaze support, hence I rescued the
>> >>>>> > old
>> >>>>> > patch
>> >>>>> > from the archives, merged it against latest git revision and
>> >>>>> > published on
>> >>>>> > github.com/agamez/buildroot
>> >>>>> >
>> >>>>> > I attach the new patch, should apply cleanly to latest version on
>> >>>>> > git.
>> >>>>> >
>> >>>>> > Even though Stephan Hoffmann work is pretty good, I think the path
>> >>>>> > of
>> >>>>> > the
>> >>>>> > new files should be modified from
>> >>>>> > board/relinux/avnet_LX9MicroBoard/
>> >>>>> > to
>> >>>>> > board/avnet/LX9MicroBoard/
>> >>>>> >
>> >>>>> > I didn't want to do that myself out of respect for the real author
>> >>>>> > of
>> >>>>> > the
>> >>>>> > patch, since this is merely a repost.
>> >>>>> >
>> >>>>> > Regards,
>> >>>>> >
>> >>>>> > Álvaro Gámez Machado
>> >>>>> >
>> >>>>> > From f4345407e3f23ebda7d91c53d81413cea51e1381 Mon Sep 17 00:00:00
>> >>>>> > 2001
>> >>>>> > From: Stephan Hoffmann <sho at relinux.de>
>> >>>>> > Date: Wed, 23 Nov 2011 11:42:40 +0100
>> >>>>> > Subject: [PATCH] Added support for the Microblaze soft CPU
>> >>>>> >
>> >>>>> > ---
>> >>>>> > board/relinux/avnet_LX9MicroBoard/README | 64 +++++
>> >>>>> > board/relinux/avnet_LX9MicroBoard/TODO | 19 ++
>> >>>>> > board/relinux/avnet_LX9MicroBoard/lx9_mmu.dts | 247
>> >>>>> > ++++++++++++++++++++
>> >>>>> > .../relinux/avnet_LX9MicroBoard/lx9_mmu_defconfig | 68 ++++++
>> >>>>> > configs/spartan6lx9_mb_defconfig | 17 ++
>> >>>>> > linux/Config.in | 8 +
>> >>>>> > linux/linux.mk | 12 +
>> >>>>> > target/Config.in.arch | 6 +-
>> >>>>> > 8 files changed, 440 insertions(+), 1 deletions(-)
>> >>>>> > create mode 100644 board/relinux/avnet_LX9MicroBoard/README
>> >>>>> > create mode 100644 board/relinux/avnet_LX9MicroBoard/TODO
>> >>>>> > create mode 100644 board/relinux/avnet_LX9MicroBoard/lx9_mmu.dts
>> >>>>> > create mode 100644
>> >>>>> > board/relinux/avnet_LX9MicroBoard/lx9_mmu_defconfig
>> >>>>> > create mode 100644 configs/spartan6lx9_mb_defconfig
>> >>>>> >
>> >>>>> > diff --git a/board/relinux/avnet_LX9MicroBoard/README
>> >>>>> > b/board/relinux/avnet_LX9MicroBoard/README
>> >>>>> > new file mode 100644
>> >>>>> > index 0000000..a2e9247
>> >>>>> > --- /dev/null
>> >>>>> > +++ b/board/relinux/avnet_LX9MicroBoard/README
>> >>>>> > @@ -0,0 +1,64 @@
>> >>>>> > +This is the buildroot board support for the Avnet Spartan6 LX9
>> >>>>> > MicroBoard.
>> >>>>> > +
>> >>>>> > +The board can be bought from Avnet or from Trenz for a low prize.
>> >>>>> > +
>> >>>>> > +To run the Linux built with buildroot you have to install the
>> >>>>> > FPGA
>> >>>>> > bitfile
>> >>>>> > +and the u-boot boot loader as described in the totorial available
>> >>>>> > on
>> >>>>> > +
>> >>>>> > + http://www.em.avnet.com/s6microboard
>> >>>>> > +
>> >>>>> > +The image file (default name is simpleImage.lx9_mmu.ub) has to be
>> >>>>> > +copied to your tftp folder (often /tftpboot/).
>> >>>>> > +
>> >>>>> > +Sample session:
>> >>>>> > +
>> >>>>> > +SPI Bootloader
>> >>>>> > +Loading binary image
>> >>>>> > +from flash @ address: 00060000
>> >>>>> > +to RAM address: 83f00000
>> >>>>> > +Done
>> >>>>> > +
>> >>>>> > +
>> >>>>> > +SDRAM :
>> >>>>> > + Icache:ON
>> >>>>> > + Dcache:ON
>> >>>>> > + U-Boot Start:0x83f00000
>> >>>>> > +SF: Got idcode 20 ba 18 10 01
>> >>>>> > +*** Warning - bad CRC, using default environment
>> >>>>> > +
>> >>>>> > +Net: Xilinx_Emaclite
>> >>>>> > +MAC: 00:0a:35:00:63:37
>> >>>>> > +U-BOOT for Avnet-LX9-Microboard-AXI-tiny-13.1
>> >>>>> > +
>> >>>>> > +BOOTP broadcast 1
>> >>>>> > +DHCP client bound to address 192.168.11.122
>> >>>>> > +Hit any key to stop autoboot: 0
>> >>>>> > +U-Boot-PetaLinux> tftp simpleImage.lx9_mmu.ub
>> >>>>> > +Using Xilinx_Emaclite device
>> >>>>> > +TFTP from server 192.168.11.10; our IP address is 192.168.11.122
>> >>>>> > +Filename 't.ub'.
>> >>>>> > +Load address: 0x80002000
>> >>>>> > +Loading:
>> >>>>> > #################################################################
>> >>>>> > +
>> >>>>> > #################################################################
>> >>>>> > +
>> >>>>> > #################################################################
>> >>>>> > +
>> >>>>> > #################################################################
>> >>>>> > +
>> >>>>> > #################################################################
>> >>>>> > + ##############################
>> >>>>> > +done
>> >>>>> > +Bytes transferred = 5207724 (4f76ac hex)
>> >>>>> > +U-Boot-PetaLinux> bootm
>> >>>>> > +## Booting kernel from Legacy Image at 80002000 ...
>> >>>>> > + Image Name: Linux-3.1.0
>> >>>>> > + Image Type: MicroBlaze Linux Kernel Image (uncompressed)
>> >>>>> > + Data Size: 5207660 Bytes = 5 MB
>> >>>>> > + Load Address: 80000000
>> >>>>> > + Entry Point: 80000000
>> >>>>> > + Verifying Checksum ... OK
>> >>>>> > + Loading Kernel Image ... OK
>> >>>>> > +OK
>> >>>>> > +## Transferring control to Linux (at address 80000000),
>> >>>>> > 0x80000000
>> >>>>> > ramdisk
>> >>>>> > 0x00000000, FDT 0x00000000...
>> >>>>> > +Early console on uartlite at 0x40600000
>> >>>>> > +..... boot log skipped
>> >>>>> > +
>> >>>>> > +Welcome to Microblaze Buildroot
>> >>>>> > +Microblaze login:
>> >>>>> > diff --git a/board/relinux/avnet_LX9MicroBoard/TODO
>> >>>>> > b/board/relinux/avnet_LX9MicroBoard/TODO
>> >>>>> > new file mode 100644
>> >>>>> > index 0000000..ca5ee94
>> >>>>> > --- /dev/null
>> >>>>> > +++ b/board/relinux/avnet_LX9MicroBoard/TODO
>> >>>>> > @@ -0,0 +1,19 @@
>> >>>>> > +TODO list for the Spartan LX9 Microboard
>> >>>>> > +
>> >>>>> > +Generate u-boot within buildroot
>> >>>>> > +================================
>> >>>>> > +Currently, we need to use the u-boot provided by Avnet.
>> >>>>> > +
>> >>>>> > +Provide config files for qemu
>> >>>>> > +=============================
>> >>>>> > +
>> >>>>> > +Generate toolchain
>> >>>>> > +==================
>> >>>>> > +Currently the GNU toolchain provided by Xilinx has to be used.
>> >>>>> > +Xilinx does not provide a toolchain suitable to build a mmu-less
>> >>>>> > +Linux system, but omitting the mmu saved space within the FPGA.
>> >>>>> > +
>> >>>>> > +Bring up mmu-less system
>> >>>>> > +========================
>> >>>>> > +Hopefully this is easy as soon as we have a working toolchain
>> >>>>> > +with flt support.
>> >>>>> > diff --git a/board/relinux/avnet_LX9MicroBoard/lx9_mmu.dts
>> >>>>> > b/board/relinux/avnet_LX9MicroBoard/lx9_mmu.dts
>> >>>>> > new file mode 100644
>> >>>>> > index 0000000..8ffedd9
>> >>>>> > --- /dev/null
>> >>>>> > +++ b/board/relinux/avnet_LX9MicroBoard/lx9_mmu.dts
>> >>>>> > @@ -0,0 +1,247 @@
>> >>>>> > +/*
>> >>>>> > + * Device Tree Generator version: 1.3
>> >>>>> > + *
>> >>>>> > + * (C) Copyright 2007-2008 Xilinx, Inc.
>> >>>>> > + * (C) Copyright 2007-2009 Michal Simek
>> >>>>> > + *
>> >>>>> > + * Michal SIMEK <monstr at monstr.eu>
>> >>>>> > + *
>> >>>>> > + * This program is free software; you can redistribute it and/or
>> >>>>> > + * modify it under the terms of the GNU General Public License as
>> >>>>> > + * published by the Free Software Foundation; either version 2 of
>> >>>>> > + * the License, or (at your option) any later version.
>> >>>>> > + *
>> >>>>> > + * This program is distributed in the hope that it will be
>> >>>>> > useful,
>> >>>>> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> >>>>> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> >>>>> > + * GNU General Public License for more details.
>> >>>>> > + *
>> >>>>> > + * You should have received a copy of the GNU General Public
>> >>>>> > License
>> >>>>> > + * along with this program; if not, write to the Free Software
>> >>>>> > + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
>> >>>>> > + * MA 02111-1307 USA
>> >>>>> > + *
>> >>>>> > + * CAUTION: This file is automatically generated by libgen.
>> >>>>> > + * Version: Xilinx EDK 13.2 EDK_O.61xd
>> >>>>> > + *
>> >>>>> > + * XPS project directory: device-tree_bsp_230-orig
>> >>>>> > + */
>> >>>>> > +
>> >>>>> > +/dts-v1/;
>> >>>>> > +/ {
>> >>>>> > + #address-cells = <1>;
>> >>>>> > + #size-cells = <1>;
>> >>>>> > + compatible = "xlnx,microblaze";
>> >>>>> > + model = "testing";
>> >>>>> > + MCB3_LPDDR: memory at 80000000 {
>> >>>>> > + device_type = "memory";
>> >>>>> > + reg = < 0x80000000 0x4000000 >;
>> >>>>> > + } ;
>> >>>>> > + aliases {
>> >>>>> > + ethernet0 = &Ethernet_MAC;
>> >>>>> > + serial0 = &USB_Uart;
>> >>>>> > + } ;
>> >>>>> > + chosen {
>> >>>>> > + bootargs = "console=ttyUL0";
>> >>>>> > + linux,stdout-path = "/axi at 0/serial at 40600000";
>> >>>>> > + } ;
>> >>>>> > + cpus {
>> >>>>> > + #address-cells = <1>;
>> >>>>> > + #cpus = <0x1>;
>> >>>>> > + #size-cells = <0>;
>> >>>>> > + microblaze_0: cpu at 0 {
>> >>>>> > + clock-frequency = <66666667>;
>> >>>>> > + compatible = "xlnx,microblaze-8.20.a";
>> >>>>> > + d-cache-baseaddr = <0x80000000>;
>> >>>>> > + d-cache-highaddr = <0x83ffffff>;
>> >>>>> > + d-cache-line-size = <0x10>;
>> >>>>> > + d-cache-size = <0x2000>;
>> >>>>> > + device_type = "cpu";
>> >>>>> > + i-cache-baseaddr = <0x80000000>;
>> >>>>> > + i-cache-highaddr = <0x83ffffff>;
>> >>>>> > + i-cache-line-size = <0x10>;
>> >>>>> > + i-cache-size = <0x2000>;
>> >>>>> > + model = "microblaze,8.20.a";
>> >>>>> > + reg = <0>;
>> >>>>> > + timebase-frequency = <66666667>;
>> >>>>> > + xlnx,addr-tag-bits = <0xd>;
>> >>>>> > + xlnx,allow-dcache-wr = <0x1>;
>> >>>>> > + xlnx,allow-icache-wr = <0x1>;
>> >>>>> > + xlnx,area-optimized = <0x0>;
>> >>>>> > + xlnx,avoid-primitives = <0x0>;
>> >>>>> > + xlnx,branch-target-cache-size = <0x0>;
>> >>>>> > + xlnx,cache-byte-size = <0x2000>;
>> >>>>> > + xlnx,d-axi = <0x1>;
>> >>>>> > + xlnx,d-lmb = <0x1>;
>> >>>>> > + xlnx,d-plb = <0x0>;
>> >>>>> > + xlnx,data-size = <0x20>;
>> >>>>> > + xlnx,dcache-addr-tag = <0xd>;
>> >>>>> > + xlnx,dcache-always-used = <0x1>;
>> >>>>> > + xlnx,dcache-byte-size = <0x2000>;
>> >>>>> > + xlnx,dcache-data-width = <0x0>;
>> >>>>> > + xlnx,dcache-force-tag-lutram = <0x0>;
>> >>>>> > + xlnx,dcache-interface = <0x0>;
>> >>>>> > + xlnx,dcache-line-len = <0x4>;
>> >>>>> > + xlnx,dcache-use-fsl = <0x0>;
>> >>>>> > + xlnx,dcache-use-writeback = <0x0>;
>> >>>>> > + xlnx,dcache-victims = <0x0>;
>> >>>>> > + xlnx,debug-enabled = <0x1>;
>> >>>>> > + xlnx,div-zero-exception = <0x0>;
>> >>>>> > + xlnx,dynamic-bus-sizing = <0x1>;
>> >>>>> > + xlnx,ecc-use-ce-exception = <0x0>;
>> >>>>> > + xlnx,edge-is-positive = <0x1>;
>> >>>>> > + xlnx,endianness = <0x1>;
>> >>>>> > + xlnx,family = "spartan6";
>> >>>>> > + xlnx,fault-tolerant = <0x0>;
>> >>>>> > + xlnx,fpu-exception = <0x0>;
>> >>>>> > + xlnx,freq = <0x3f940ab>;
>> >>>>> > + xlnx,fsl-data-size = <0x20>;
>> >>>>> > + xlnx,fsl-exception = <0x0>;
>> >>>>> > + xlnx,fsl-links = <0x0>;
>> >>>>> > + xlnx,i-axi = <0x0>;
>> >>>>> > + xlnx,i-lmb = <0x1>;
>> >>>>> > + xlnx,i-plb = <0x0>;
>> >>>>> > + xlnx,icache-always-used = <0x1>;
>> >>>>> > + xlnx,icache-data-width = <0x0>;
>> >>>>> > + xlnx,icache-force-tag-lutram = <0x0>;
>> >>>>> > + xlnx,icache-interface = <0x0>;
>> >>>>> > + xlnx,icache-line-len = <0x4>;
>> >>>>> > + xlnx,icache-streams = <0x0>;
>> >>>>> > + xlnx,icache-use-fsl = <0x0>;
>> >>>>> > + xlnx,icache-victims = <0x0>;
>> >>>>> > + xlnx,ill-opcode-exception = <0x0>;
>> >>>>> > + xlnx,instance = "microblaze_0";
>> >>>>> > + xlnx,interconnect = <0x2>;
>> >>>>> > + xlnx,interconnect-m-axi-dc-aw-register = <0x0>;
>> >>>>> > + xlnx,interconnect-m-axi-dc-read-issuing = <0x2>;
>> >>>>> > + xlnx,interconnect-m-axi-dc-w-register = <0x0>;
>> >>>>> > + xlnx,interconnect-m-axi-dc-write-issuing = <0x20>;
>> >>>>> > + xlnx,interconnect-m-axi-dp-read-issuing = <0x1>;
>> >>>>> > + xlnx,interconnect-m-axi-dp-write-issuing = <0x1>;
>> >>>>> > + xlnx,interconnect-m-axi-ic-read-issuing = <0x2>;
>> >>>>> > + xlnx,interconnect-m-axi-ip-read-issuing = <0x1>;
>> >>>>> > + xlnx,interrupt-is-edge = <0x0>;
>> >>>>> > + xlnx,lockstep-slave = <0x0>;
>> >>>>> > + xlnx,mmu-dtlb-size = <0x1>;
>> >>>>> > + xlnx,mmu-itlb-size = <0x1>;
>> >>>>> > + xlnx,mmu-privileged-instr = <0x0>;
>> >>>>> > + xlnx,mmu-tlb-access = <0x3>;
>> >>>>> > + xlnx,mmu-zones = <0x2>;
>> >>>>> > + xlnx,number-of-pc-brk = <0x1>;
>> >>>>> > + xlnx,number-of-rd-addr-brk = <0x0>;
>> >>>>> > + xlnx,number-of-wr-addr-brk = <0x0>;
>> >>>>> > + xlnx,opcode-0x0-illegal = <0x0>;
>> >>>>> > + xlnx,optimization = <0x0>;
>> >>>>> > + xlnx,pvr = <0x0>;
>> >>>>> > + xlnx,pvr-user1 = <0x0>;
>> >>>>> > + xlnx,pvr-user2 = <0x0>;
>> >>>>> > + xlnx,reset-msr = <0x0>;
>> >>>>> > + xlnx,sco = <0x0>;
>> >>>>> > + xlnx,stream-interconnect = <0x0>;
>> >>>>> > + xlnx,unaligned-exceptions = <0x0>;
>> >>>>> > + xlnx,use-barrel = <0x1>;
>> >>>>> > + xlnx,use-branch-target-cache = <0x0>;
>> >>>>> > + xlnx,use-dcache = <0x1>;
>> >>>>> > + xlnx,use-div = <0x0>;
>> >>>>> > + xlnx,use-ext-brk = <0x1>;
>> >>>>> > + xlnx,use-ext-nm-brk = <0x1>;
>> >>>>> > + xlnx,use-extended-fsl-instr = <0x0>;
>> >>>>> > + xlnx,use-fpu = <0x0>;
>> >>>>> > + xlnx,use-hw-mul = <0x1>;
>> >>>>> > + xlnx,use-icache = <0x1>;
>> >>>>> > + xlnx,use-interrupt = <0x1>;
>> >>>>> > + xlnx,use-mmu = <0x3>;
>> >>>>> > + xlnx,use-msr-instr = <0x1>;
>> >>>>> > + xlnx,use-pcmp-instr = <0x0>;
>> >>>>> > + xlnx,use-stack-protection = <0x0>;
>> >>>>> > + } ;
>> >>>>> > + } ;
>> >>>>> > + axi4lite_0: axi at 0 {
>> >>>>> > + #address-cells = <1>;
>> >>>>> > + #size-cells = <1>;
>> >>>>> > + compatible = "xlnx,axi-interconnect-1.03.a",
>> >>>>> > "simple-bus";
>> >>>>> > + ranges ;
>> >>>>> > + Ethernet_MAC: ethernet at 40e00000 {
>> >>>>> > + compatible = "xlnx,axi-ethernetlite-1.00.a",
>> >>>>> > "xlnx,xps-ethernetlite-1.00.a";
>> >>>>> > + device_type = "network";
>> >>>>> > + interrupt-parent = <µblaze_0_intc>;
>> >>>>> > + interrupts = < 2 0 >;
>> >>>>> > + local-mac-address = [ 00 0a 35 aa de 00 ];
>> >>>>> > +// phy-handle = <&phy0>;
>> >>>>> > + reg = < 0x40e00000 0x10000 >;
>> >>>>> > + xlnx,duplex = <0x1>;
>> >>>>> > + xlnx,family = "spartan6";
>> >>>>> > + xlnx,include-global-buffers = <0x0>;
>> >>>>> > + xlnx,include-internal-loopback = <0x0>;
>> >>>>> > + xlnx,include-mdio = <0x1>;
>> >>>>> > + xlnx,include-phy-constraints = <0x1>;
>> >>>>> > + xlnx,interconnect-s-axi-read-acceptance = <0x1>;
>> >>>>> > + xlnx,interconnect-s-axi-write-acceptance = <0x1>;
>> >>>>> > + xlnx,rx-ping-pong = <0x0>;
>> >>>>> > + xlnx,s-axi-aclk-period-ps = <0x3a98>;
>> >>>>> > + xlnx,s-axi-id-width = <0x1>;
>> >>>>> > + xlnx,s-axi-supports-narrow-burst = <0x0>;
>> >>>>> > + xlnx,tx-ping-pong = <0x0>;
>> >>>>> > +/*
>> >>>>> > + mdio {
>> >>>>> > + #address-cells = <1>;
>> >>>>> > + #size-cells = <0>;
>> >>>>> > + phy0: phy at 7 {
>> >>>>> > + compatible = "marvell,88e1111";
>> >>>>> > + device_type = "ethernet-phy";
>> >>>>> > + reg = <7>;
>> >>>>> > + } ;
>> >>>>> > + } ;
>> >>>>> > +*/
>> >>>>> > + } ;
>> >>>>> > + SPI_FLASH: spi at 40a00000 {
>> >>>>> > + compatible = "xlnx,axi-spi-1.01.a",
>> >>>>> > "xlnx,xps-spi-2.00.a";
>> >>>>> > + interrupt-parent = <µblaze_0_intc>;
>> >>>>> > + interrupts = < 1 2 >;
>> >>>>> > + reg = < 0x40a00000 0x10000 >;
>> >>>>> > + xlnx,family = "spartan6";
>> >>>>> > + xlnx,fifo-exist = <0x1>;
>> >>>>> > + xlnx,num-ss-bits = <0x1>;
>> >>>>> > + xlnx,num-transfer-bits = <0x8>;
>> >>>>> > + xlnx,sck-ratio = <0x4>;
>> >>>>> > + } ;
>> >>>>> > + USB_Uart: serial at 40600000 {
>> >>>>> > + clock-frequency = <66666667>;
>> >>>>> > + compatible = "xlnx,axi-uartlite-1.02.a",
>> >>>>> > "xlnx,xps-uartlite-1.00.a";
>> >>>>> > + current-speed = <115200>;
>> >>>>> > + device_type = "serial";
>> >>>>> > + interrupt-parent = <µblaze_0_intc>;
>> >>>>> > + interrupts = < 3 0 >;
>> >>>>> > + port-number = <0>;
>> >>>>> > + reg = < 0x40600000 0x10000 >;
>> >>>>> > + xlnx,baudrate = <0x1c200>;
>> >>>>> > + xlnx,data-bits = <0x8>;
>> >>>>> > + xlnx,family = "spartan6";
>> >>>>> > + xlnx,odd-parity = <0x1>;
>> >>>>> > + xlnx,s-axi-aclk-freq-hz = <0x3f940ab>;
>> >>>>> > + xlnx,use-parity = <0x0>;
>> >>>>> > + } ;
>> >>>>> > + microblaze_0_intc: interrupt-controller at 41200000 {
>> >>>>> > + #interrupt-cells = <0x2>;
>> >>>>> > + compatible = "xlnx,axi-intc-1.01.a",
>> >>>>> > "xlnx,xps-intc-1.00.a";
>> >>>>> > + interrupt-controller ;
>> >>>>> > + reg = < 0x41200000 0x10000 >;
>> >>>>> > + xlnx,kind-of-intr = <0xc>;
>> >>>>> > + xlnx,num-intr-inputs = <0x4>;
>> >>>>> > + } ;
>> >>>>> > + system_timer: timer at 41c00000 {
>> >>>>> > + clock-frequency = <66666667>;
>> >>>>> > + compatible = "xlnx,axi-timer-1.02.a",
>> >>>>> > "xlnx,xps-timer-1.00.a";
>> >>>>> > + interrupt-parent = <µblaze_0_intc>;
>> >>>>> > + interrupts = < 0 2 >;
>> >>>>> > + reg = < 0x41c00000 0x10000 >;
>> >>>>> > + xlnx,count-width = <0x20>;
>> >>>>> > + xlnx,family = "spartan6";
>> >>>>> > + xlnx,gen0-assert = <0x1>;
>> >>>>> > + xlnx,gen1-assert = <0x1>;
>> >>>>> > + xlnx,one-timer-only = <0x0>;
>> >>>>> > + xlnx,trig0-assert = <0x1>;
>> >>>>> > + xlnx,trig1-assert = <0x1>;
>> >>>>> > + } ;
>> >>>>> > + } ;
>> >>>>> > +} ;
>> >>>>> > diff --git a/board/relinux/avnet_LX9MicroBoard/lx9_mmu_defconfig
>> >>>>> > b/board/relinux/avnet_LX9MicroBoard/lx9_mmu_defconfig
>> >>>>> > new file mode 100644
>> >>>>> > index 0000000..5d01ca0
>> >>>>> > --- /dev/null
>> >>>>> > +++ b/board/relinux/avnet_LX9MicroBoard/lx9_mmu_defconfig
>> >>>>> > @@ -0,0 +1,68 @@
>> >>>>> > +CONFIG_EXPERIMENTAL=y
>> >>>>> > +CONFIG_SYSVIPC=y
>> >>>>> > +CONFIG_IKCONFIG=y
>> >>>>> > +CONFIG_IKCONFIG_PROC=y
>> >>>>> > +CONFIG_BLK_DEV_INITRD=y
>> >>>>> > +CONFIG_INITRAMFS_SOURCE="rootfs.cpio"
>> >>>>> > +CONFIG_INITRAMFS_COMPRESSION_GZIP=y
>> >>>>> > +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
>> >>>>> > +CONFIG_EXPERT=y
>> >>>>> > +CONFIG_KALLSYMS_ALL=y
>> >>>>> > +CONFIG_KALLSYMS_EXTRA_PASS=y
>> >>>>> > +# CONFIG_HOTPLUG is not set
>> >>>>> > +# CONFIG_BASE_FULL is not set
>> >>>>> > +# CONFIG_FUTEX is not set
>> >>>>> > +# CONFIG_EPOLL is not set
>> >>>>> > +# CONFIG_SIGNALFD is not set
>> >>>>> > +# CONFIG_SHMEM is not set
>> >>>>> > +CONFIG_SLAB=y
>> >>>>> > +CONFIG_MODULES=y
>> >>>>> > +CONFIG_MODULE_UNLOAD=y
>> >>>>> > +# CONFIG_BLK_DEV_BSG is not set
>> >>>>> > +# CONFIG_OPT_LIB_ASM is not set
>> >>>>> > +CONFIG_KERNEL_BASE_ADDR=0x80000000
>> >>>>> > +CONFIG_XILINX_MICROBLAZE0_FAMILY="spartan6"
>> >>>>> > +CONFIG_XILINX_MICROBLAZE0_USE_MSR_INSTR=1
>> >>>>> > +# CONFIG_XILINX_MICROBLAZE0_USE_PCMP_INSTR is not set
>> >>>>> > +CONFIG_XILINX_MICROBLAZE0_USE_BARREL=1
>> >>>>> > +CONFIG_XILINX_MICROBLAZE0_USE_HW_MUL=1
>> >>>>> > +CONFIG_XILINX_MICROBLAZE0_HW_VER="8.20.a"
>> >>>>> > +CONFIG_HZ_100=y
>> >>>>> > +CONFIG_MMU=y
>> >>>>> > +CONFIG_CMDLINE_BOOL=y
>> >>>>> > +CONFIG_CMDLINE_FORCE=y
>> >>>>> > +CONFIG_NET=y
>> >>>>> > +CONFIG_PACKET=y
>> >>>>> > +CONFIG_UNIX=y
>> >>>>> > +CONFIG_INET=y
>> >>>>> > +# CONFIG_INET_LRO is not set
>> >>>>> > +# CONFIG_IPV6 is not set
>> >>>>> > +CONFIG_PROC_DEVICETREE=y
>> >>>>> > +CONFIG_BLK_DEV_RAM=y
>> >>>>> > +CONFIG_BLK_DEV_RAM_SIZE=8192
>> >>>>> > +CONFIG_NETDEVICES=y
>> >>>>> > +CONFIG_NET_ETHERNET=y
>> >>>>> > +CONFIG_XILINX_EMACLITE=y
>> >>>>> > +# CONFIG_INPUT is not set
>> >>>>> > +# CONFIG_SERIO is not set
>> >>>>> > +# CONFIG_VT is not set
>> >>>>> > +CONFIG_SERIAL_UARTLITE=y
>> >>>>> > +CONFIG_SERIAL_UARTLITE_CONSOLE=y
>> >>>>> > +# CONFIG_HW_RANDOM is not set
>> >>>>> > +# CONFIG_HWMON is not set
>> >>>>> > +# CONFIG_USB_SUPPORT is not set
>> >>>>> > +CONFIG_EXT2_FS=y
>> >>>>> > +# CONFIG_DNOTIFY is not set
>> >>>>> > +CONFIG_NFS_FS=y
>> >>>>> > +CONFIG_NFS_V3=y
>> >>>>> > +CONFIG_CIFS=y
>> >>>>> > +CONFIG_CIFS_STATS=y
>> >>>>> > +CONFIG_CIFS_STATS2=y
>> >>>>> > +CONFIG_PARTITION_ADVANCED=y
>> >>>>> > +CONFIG_DEBUG_KERNEL=y
>> >>>>> > +CONFIG_DETECT_HUNG_TASK=y
>> >>>>> > +CONFIG_DEBUG_SLAB=y
>> >>>>> > +CONFIG_DEBUG_SPINLOCK=y
>> >>>>> > +CONFIG_DEBUG_INFO=y
>> >>>>> > +CONFIG_EARLY_PRINTK=y
>> >>>>> > +# CONFIG_CRYPTO_ANSI_CPRNG is not set
>> >>>>> > diff --git a/configs/spartan6lx9_mb_defconfig
>> >>>>> > b/configs/spartan6lx9_mb_defconfig
>> >>>>> > new file mode 100644
>> >>>>> > index 0000000..0329bb4
>> >>>>> > --- /dev/null
>> >>>>> > +++ b/configs/spartan6lx9_mb_defconfig
>> >>>>> > @@ -0,0 +1,17 @@
>> >>>>> > +BR2_microblaze=y
>> >>>>> > +BR2_TOOLCHAIN_EXTERNAL=y
>> >>>>> >
>> >>>>> > +BR2_TOOLCHAIN_EXTERNAL_PATH="/opt/microblazeel-unknown-linux-gnu/"
>> >>>>> >
>> >>>>> >
>> >>>>> > +BR2_TOOLCHAIN_EXTERNAL_CUSTOM_PREFIX="microblazeel-unknown-linux-gnu"
>> >>>>> > +BR2_TOOLCHAIN_EXTERNAL_CUSTOM_GLIBC=y
>> >>>>> > +BR2_TOOLCHAIN_EXTERNAL_CXX=y
>> >>>>> > +BR2_TARGET_GENERIC_HOSTNAME="Microblaze Buildroot"
>> >>>>> > +BR2_TARGET_GENERIC_ISSUE="Welcome to Microblaze Buildroot"
>> >>>>> > +BR2_TARGET_GENERIC_GETTY_PORT="ttyUL0"
>> >>>>> > +# BR2_TARGET_ROOTFS_TAR is not set
>> >>>>> > +BR2_TARGET_ROOTFS_INITRAMFS=y
>> >>>>> > +BR2_LINUX_KERNEL=y
>> >>>>> > +BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
>> >>>>> >
>> >>>>> >
>> >>>>> > +BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="$(TOPDIR)/board/relinux/avnet_LX9MicroBoard/lx9_mmu_defconfig"
>> >>>>> >
>> >>>>> >
>> >>>>> > +BR2_LINUX_KERNEL_DTS_FILE="$(TOPDIR)/board/relinux/avnet_LX9MicroBoard/lx9_mmu.dts"
>> >>>>> > +BR2_LINUX_KERNEL_IMAGE_TARGET_CUSTOM=y
>> >>>>> > +BR2_LINUX_KERNEL_IMAGE_TARGET_NAME="simpleImage.lx9_mmu"
>> >>>>> > diff --git a/linux/Config.in b/linux/Config.in
>> >>>>> > index 86dc32a..138feb3 100644
>> >>>>> > --- a/linux/Config.in
>> >>>>> > +++ b/linux/Config.in
>> >>>>> > @@ -120,6 +120,14 @@ config BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE
>> >>>>> > help
>> >>>>> > Path to the kernel configuration file
>> >>>>> >
>> >>>>> > +config BR2_LINUX_KERNEL_DTS_FILE
>> >>>>> > + string "Device Tree dts file location"
>> >>>>> > + depends on BR2_microblaze
>> >>>>> > + help
>> >>>>> > + Path from where the dts file has to be copied
>> >>>>> > + The final "custom target" name depends on the
>> >>>>> > + dts file name:
>> >>>>> > + <name>.dts --> simpleImage.<name>
>> >>>>> > #
>> >>>>> > # Binary format
>> >>>>> > #
>> >>>>> > diff --git a/linux/linux.mk b/linux/linux.mk
>> >>>>> > index ae236d4..4a24f18 100644
>> >>>>> > --- a/linux/linux.mk
>> >>>>> > +++ b/linux/linux.mk
>> >>>>> > @@ -117,6 +117,18 @@ endef
>> >>>>> >
>> >>>>> > LINUX_POST_PATCH_HOOKS += LINUX_APPLY_PATCHES
>> >>>>> >
>> >>>>> > +ifeq ($(KERNEL_ARCH),microblaze)
>> >>>>> > +# on microblaze, we always want mkimage
>> >>>>> > +LINUX_DEPENDENCIES+=host-uboot-tools
>> >>>>> > +
>> >>>>> > +define LINUX_COPY_DTS
>> >>>>> > + if test -f "$(BR2_LINUX_KERNEL_DTS_FILE)" ; then \
>> >>>>> > + cp $(BR2_LINUX_KERNEL_DTS_FILE)
>> >>>>> > $(@D)/arch/microblaze/boot/dts ; \
>> >>>>> > + else \
>> >>>>> > + echo "Cannot copy dts file!" ; \
>> >>>>> > + fi
>> >>>>> > +endef
>> >>>>> > +endif
>> >>>>> >
>> >>>>> > ifeq ($(BR2_LINUX_KERNEL_USE_DEFCONFIG),y)
>> >>>>> > KERNEL_SOURCE_CONFIG = $(KERNEL_ARCH_PATH)/configs/$(call
>> >>>>> > qstrip,$(BR2_LINUX_KERNEL_DEFCONFIG))_defconfig
>> >>>>> > diff --git a/target/Config.in.arch b/target/Config.in.arch
>> >>>>> > index 417441d..3a75585 100644
>> >>>>> > --- a/target/Config.in.arch
>> >>>>> > +++ b/target/Config.in.arch
>> >>>>> > @@ -21,6 +21,8 @@ config BR2_i386
>> >>>>> > config BR2_m68k
>> >>>>> > bool "m68k"
>> >>>>> > depends on BROKEN # ice in uclibc / inet_ntoa_r
>> >>>>> > +config BR2_microblaze
>> >>>>> > + bool "microblaze"
>> >>>>> > config BR2_mips
>> >>>>> > bool "mips"
>> >>>>> > config BR2_mipsel
>> >>>>> > @@ -508,6 +510,7 @@ config BR2_ARCH
>> >>>>> > default "i686" if BR2_x86_athlon
>> >>>>> > default "i686" if BR2_x86_athlon_4
>> >>>>> > default "m68k" if BR2_m68k
>> >>>>> > + default "microblaze" if BR2_microblaze
>> >>>>> > default "mips" if BR2_mips
>> >>>>> > default "mipsel" if BR2_mipsel
>> >>>>> > default "powerpc" if BR2_powerpc
>> >>>>> > @@ -533,7 +536,7 @@ config BR2_ARCH
>> >>>>> >
>> >>>>> > config BR2_ENDIAN
>> >>>>> > string
>> >>>>> > - default "LITTLE" if BR2_arm || BR2_bfin || BR2_i386 ||
>> >>>>> > BR2_mipsel || \
>> >>>>> > + default "LITTLE" if BR2_arm || BR2_bfin || BR2_i386 ||
>> >>>>> > BR2_mipsel ||
>> >>>>> > BR2_microblaze || \
>> >>>>> > BR2_sh3 || BR2_sh4 || BR2_sh4a || BR2_x86_64 ||
>> >>>>> > BR2_sh64
>> >>>>> > default "BIG" if BR2_armeb || BR2_avr32 || BR2_m68k ||
>> >>>>> > BR2_mips || \
>> >>>>> > BR2_powerpc || BR2_sh2 || BR2_sh2a || \
>> >>>>> > @@ -598,6 +601,7 @@ config BR2_GCC_TARGET_TUNE
>> >>>>> > default 68030 if BR2_m68k_68030
>> >>>>> > default 68040 if BR2_m68k_68040
>> >>>>> > default 68060 if BR2_m68k_68060
>> >>>>> > + default microblaze if BR2_microblaze
>> >>>>> > default mips1 if BR2_mips_1
>> >>>>> > default mips2 if BR2_mips_2
>> >>>>> > default mips3 if BR2_mips_3
>> >>>>> > --
>> >>>>> > 1.7.9
>> >>>>> >
>> >>>>> >
>> >>>>> >
>> >>>>> > 2012/2/11 <buildroot-request at busybox.net>
>> >>>>> >>
>> >>>>> >>
>> >>>>> >> On Saturday 11 February 2012 05:58:37 Spenser Gilliland wrote:
>> >>>>> >> > I'm using this Microblaze patch for my project. Will it be
>> >>>>> >> > part
>> >>>>> >> > of
>> >>>>> >> > the official release that is coming up soon?
>> >>>>> >>
>> >>>>> >> I'm afraid it got lost between the cracks. Could you repost it?
>> >>>>> >>
>> >>>>> >> Regards,
>> >>>>> >> Arnout
>> >>>>> >
>> >>>>> >
>> >>>>> >
>> >>>>> > _______________________________________________
>> >>>>> > buildroot mailing list
>> >>>>> > buildroot at busybox.net
>> >>>>> > http://lists.busybox.net/mailman/listinfo/buildroot
>> >>>>>
>> >>>>>
>> >>>>>
>> >>>>> --
>> >>>>> Spenser Gilliland
>> >>>>> Computer Engineer
>> >>>>> Illinois Institute of Technology
>> >>>>
>> >>>>
>> >>>>
>> >>>>
>> >>>> --
>> >>>> Álvaro Gámez Machado
>> >>>>
>> >>>
>> >>>
>> >>>
>> >>> --
>> >>> Álvaro Gámez Machado
>> >>>
>> >>>
>> >>> _______________________________________________
>> >>> buildroot mailing list
>> >>> buildroot at busybox.net
>> >>> http://lists.busybox.net/mailman/listinfo/buildroot
>> >
>> >
>> >
>> >
>> > --
>> > Álvaro Gámez Machado
>> >
>>
>>
>>
>> --
>> Spenser Gilliland
>> Computer Engineer
>> Illinois Institute of Technology
>
>
>
>
> --
> Álvaro Gámez Machado
>
--
Spenser Gilliland
Computer Engineer
Illinois Institute of Technology
More information about the buildroot
mailing list