[Buildroot] [PATCH] Adding Microblaze support to Buildroot

Alvaro Gamez alvaro.gamez at hazent.com
Mon Feb 13 19:40:47 UTC 2012


I checked and this is the content of the config file:

BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="$(TOPDIR)/board/avnet/LX9MicroBoard/lx9_mmu_defconfig"
BR2_LINUX_KERNEL_DTS_FILE="$(TOPDIR)/board/avnet/LX9MicroBoard/lx9_mmu.dts"
BR2_LINUX_KERNEL_IMAGE_TARGET_NAME="simpleImage.lx9_mmu"

so I think there has to be some other thing I'm not aware of.

2012/2/13 Spenser Gilliland <spenser309 at gmail.com>

> This means that the dts was not copied into the arch/microblaze/boot/dts
> dir or you are not building the correct target.
>
> You need to verify that the BR2_LINUX_KERNEL_DTS_FILE is set to a real
> file and that BR2_LINUX_KERNEL_IMAGE_TARGET_NAME is set to
> simpleImage.$(filename-wo-extension).
>
> IE.  if BR2_LINUX_KERNEL_DTS_FILE = /path/to/dts/xupv5.dts then
> BR2_LINUX_KERNEL_IMAGE_TARGET=simpleImage.xupv5.
>
> Spenser
>
> On Feb 13, 2012 1:14 PM, "Alvaro Gamez" <alvaro.gamez at hazent.com> wrote:
>
>> Ok, now that I have a little time I'm trying to make it work.
>>
>> I haven't had any problem yet with GCC tune. However, I'm getting the
>> following error while trying to build the kernel
>>
>> make[2]: *** No rule to make target `arch/microblaze/boot/lx9_mmu.dtb',
>> needed by `arch/microblaze/boot/system.dtb'.  Stop.
>>
>> Any idea?
>>
>> Regards
>>
>>
>> 2012/2/13 Alvaro Gamez <alvaro.gamez at hazent.com>
>>
>>> I am yet to test it. I just found yersterday that buildroot exists :)
>>>
>>>
>>> 2012/2/13 Spenser Gilliland <spenser309 at gmail.com>
>>>
>>>> Alvaro,
>>>>
>>>> Did you have issues with the GCC tune?  I had to remove that line from
>>>> the original patch.
>>>>
>>>> Spenser
>>>>
>>>> On Sun, Feb 12, 2012 at 5:07 PM, Alvaro Gamez <alvaro.gamez at hazent.com>
>>>> wrote:
>>>> > Hi
>>>> >
>>>> > I am also interested on Microblaze support, hence I rescued the old
>>>> patch
>>>> > from the archives, merged it against latest git revision and
>>>> published on
>>>> > github.com/agamez/buildroot
>>>> >
>>>> > I attach the new patch, should apply cleanly to latest version on git.
>>>> >
>>>> > Even though Stephan Hoffmann work is pretty good, I think the path of
>>>> the
>>>> > new files should be modified from board/relinux/avnet_LX9MicroBoard/
>>>> to
>>>> > board/avnet/LX9MicroBoard/
>>>> >
>>>> > I didn't want to do that myself out of respect for the real author of
>>>> the
>>>> > patch, since this is merely a repost.
>>>> >
>>>> > Regards,
>>>> >
>>>> > Álvaro Gámez Machado
>>>> >
>>>> > From f4345407e3f23ebda7d91c53d81413cea51e1381 Mon Sep 17 00:00:00 2001
>>>> > From: Stephan Hoffmann <sho at relinux.de>
>>>> > Date: Wed, 23 Nov 2011 11:42:40 +0100
>>>> > Subject: [PATCH] Added support for the Microblaze soft CPU
>>>> >
>>>> > ---
>>>> >  board/relinux/avnet_LX9MicroBoard/README           |   64 +++++
>>>> >  board/relinux/avnet_LX9MicroBoard/TODO             |   19 ++
>>>> >  board/relinux/avnet_LX9MicroBoard/lx9_mmu.dts      |  247
>>>> > ++++++++++++++++++++
>>>> >  .../relinux/avnet_LX9MicroBoard/lx9_mmu_defconfig  |   68 ++++++
>>>> >  configs/spartan6lx9_mb_defconfig                   |   17 ++
>>>> >  linux/Config.in                                    |    8 +
>>>> >  linux/linux.mk                                     |   12 +
>>>> >  target/Config.in.arch                              |    6 +-
>>>> >  8 files changed, 440 insertions(+), 1 deletions(-)
>>>> >  create mode 100644 board/relinux/avnet_LX9MicroBoard/README
>>>> >  create mode 100644 board/relinux/avnet_LX9MicroBoard/TODO
>>>> >  create mode 100644 board/relinux/avnet_LX9MicroBoard/lx9_mmu.dts
>>>> >  create mode 100644
>>>> board/relinux/avnet_LX9MicroBoard/lx9_mmu_defconfig
>>>> >  create mode 100644 configs/spartan6lx9_mb_defconfig
>>>> >
>>>> > diff --git a/board/relinux/avnet_LX9MicroBoard/README
>>>> > b/board/relinux/avnet_LX9MicroBoard/README
>>>> > new file mode 100644
>>>> > index 0000000..a2e9247
>>>> > --- /dev/null
>>>> > +++ b/board/relinux/avnet_LX9MicroBoard/README
>>>> > @@ -0,0 +1,64 @@
>>>> > +This is the buildroot board support for the Avnet Spartan6 LX9
>>>> MicroBoard.
>>>> > +
>>>> > +The board can be bought from Avnet or from Trenz for a low prize.
>>>> > +
>>>> > +To run the Linux built with buildroot you have to install the FPGA
>>>> bitfile
>>>> > +and the u-boot boot loader as described in the totorial available on
>>>> > +
>>>> > +    http://www.em.avnet.com/s6microboard
>>>> > +
>>>> > +The image file (default name is simpleImage.lx9_mmu.ub) has to be
>>>> > +copied to your tftp folder (often /tftpboot/).
>>>> > +
>>>> > +Sample session:
>>>> > +
>>>> > +SPI Bootloader
>>>> > +Loading binary image
>>>> > +from flash @ address: 00060000
>>>> > +to RAM address: 83f00000
>>>> > +Done
>>>> > +
>>>> > +
>>>> > +SDRAM :
>>>> > +                Icache:ON
>>>> > +                Dcache:ON
>>>> > +        U-Boot Start:0x83f00000
>>>> > +SF: Got idcode 20 ba 18 10 01
>>>> > +*** Warning - bad CRC, using default environment
>>>> > +
>>>> > +Net:   Xilinx_Emaclite
>>>> > +MAC:   00:0a:35:00:63:37
>>>> > +U-BOOT for Avnet-LX9-Microboard-AXI-tiny-13.1
>>>> > +
>>>> > +BOOTP broadcast 1
>>>> > +DHCP client bound to address 192.168.11.122
>>>> > +Hit any key to stop autoboot:  0
>>>> > +U-Boot-PetaLinux> tftp simpleImage.lx9_mmu.ub
>>>> > +Using Xilinx_Emaclite device
>>>> > +TFTP from server 192.168.11.10; our IP address is 192.168.11.122
>>>> > +Filename 't.ub'.
>>>> > +Load address: 0x80002000
>>>> > +Loading:
>>>> #################################################################
>>>> > +
>>>> #################################################################
>>>> > +
>>>> #################################################################
>>>> > +
>>>> #################################################################
>>>> > +
>>>> #################################################################
>>>> > +         ##############################
>>>> > +done
>>>> > +Bytes transferred = 5207724 (4f76ac hex)
>>>> > +U-Boot-PetaLinux> bootm
>>>> > +## Booting kernel from Legacy Image at 80002000 ...
>>>> > +   Image Name:   Linux-3.1.0
>>>> > +   Image Type:   MicroBlaze Linux Kernel Image (uncompressed)
>>>> > +   Data Size:    5207660 Bytes =  5 MB
>>>> > +   Load Address: 80000000
>>>> > +   Entry Point:  80000000
>>>> > +   Verifying Checksum ... OK
>>>> > +   Loading Kernel Image ... OK
>>>> > +OK
>>>> > +## Transferring control to Linux (at address 80000000), 0x80000000
>>>> ramdisk
>>>> > 0x00000000, FDT 0x00000000...
>>>> > +Early console on uartlite at 0x40600000
>>>> > +..... boot log skipped
>>>> > +
>>>> > +Welcome to Microblaze Buildroot
>>>> > +Microblaze login:
>>>> > diff --git a/board/relinux/avnet_LX9MicroBoard/TODO
>>>> > b/board/relinux/avnet_LX9MicroBoard/TODO
>>>> > new file mode 100644
>>>> > index 0000000..ca5ee94
>>>> > --- /dev/null
>>>> > +++ b/board/relinux/avnet_LX9MicroBoard/TODO
>>>> > @@ -0,0 +1,19 @@
>>>> > +TODO list for the Spartan LX9 Microboard
>>>> > +
>>>> > +Generate u-boot within buildroot
>>>> > +================================
>>>> > +Currently, we need to use the u-boot provided by Avnet.
>>>> > +
>>>> > +Provide config files for qemu
>>>> > +=============================
>>>> > +
>>>> > +Generate toolchain
>>>> > +==================
>>>> > +Currently the GNU toolchain provided by Xilinx has to be used.
>>>> > +Xilinx does not provide a toolchain suitable to build a mmu-less
>>>> > +Linux system, but omitting the mmu saved space within the FPGA.
>>>> > +
>>>> > +Bring up mmu-less system
>>>> > +========================
>>>> > +Hopefully this is easy as soon as we have a working toolchain
>>>> > +with flt support.
>>>> > diff --git a/board/relinux/avnet_LX9MicroBoard/lx9_mmu.dts
>>>> > b/board/relinux/avnet_LX9MicroBoard/lx9_mmu.dts
>>>> > new file mode 100644
>>>> > index 0000000..8ffedd9
>>>> > --- /dev/null
>>>> > +++ b/board/relinux/avnet_LX9MicroBoard/lx9_mmu.dts
>>>> > @@ -0,0 +1,247 @@
>>>> > +/*
>>>> > + * Device Tree Generator version: 1.3
>>>> > + *
>>>> > + * (C) Copyright 2007-2008 Xilinx, Inc.
>>>> > + * (C) Copyright 2007-2009 Michal Simek
>>>> > + *
>>>> > + * Michal SIMEK <monstr at monstr.eu>
>>>> > + *
>>>> > + * This program is free software; you can redistribute it and/or
>>>> > + * modify it under the terms of the GNU General Public License as
>>>> > + * published by the Free Software Foundation; either version 2 of
>>>> > + * the License, or (at your option) any later version.
>>>> > + *
>>>> > + * This program is distributed in the hope that it will be useful,
>>>> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>>>> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>>>> > + * GNU General Public License for more details.
>>>> > + *
>>>> > + * You should have received a copy of the GNU General Public License
>>>> > + * along with this program; if not, write to the Free Software
>>>> > + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
>>>> > + * MA 02111-1307 USA
>>>> > + *
>>>> > + * CAUTION: This file is automatically generated by libgen.
>>>> > + * Version: Xilinx EDK 13.2 EDK_O.61xd
>>>> > + *
>>>> > + * XPS project directory: device-tree_bsp_230-orig
>>>> > + */
>>>> > +
>>>> > +/dts-v1/;
>>>> > +/ {
>>>> > +    #address-cells = <1>;
>>>> > +    #size-cells = <1>;
>>>> > +    compatible = "xlnx,microblaze";
>>>> > +    model = "testing";
>>>> > +    MCB3_LPDDR: memory at 80000000 {
>>>> > +        device_type = "memory";
>>>> > +        reg = < 0x80000000 0x4000000 >;
>>>> > +    } ;
>>>> > +    aliases {
>>>> > +        ethernet0 = &Ethernet_MAC;
>>>> > +        serial0 = &USB_Uart;
>>>> > +    } ;
>>>> > +    chosen {
>>>> > +        bootargs = "console=ttyUL0";
>>>> > +        linux,stdout-path = "/axi at 0/serial at 40600000";
>>>> > +    } ;
>>>> > +    cpus {
>>>> > +        #address-cells = <1>;
>>>> > +        #cpus = <0x1>;
>>>> > +        #size-cells = <0>;
>>>> > +        microblaze_0: cpu at 0 {
>>>> > +            clock-frequency = <66666667>;
>>>> > +            compatible = "xlnx,microblaze-8.20.a";
>>>> > +            d-cache-baseaddr = <0x80000000>;
>>>> > +            d-cache-highaddr = <0x83ffffff>;
>>>> > +            d-cache-line-size = <0x10>;
>>>> > +            d-cache-size = <0x2000>;
>>>> > +            device_type = "cpu";
>>>> > +            i-cache-baseaddr = <0x80000000>;
>>>> > +            i-cache-highaddr = <0x83ffffff>;
>>>> > +            i-cache-line-size = <0x10>;
>>>> > +            i-cache-size = <0x2000>;
>>>> > +            model = "microblaze,8.20.a";
>>>> > +            reg = <0>;
>>>> > +            timebase-frequency = <66666667>;
>>>> > +            xlnx,addr-tag-bits = <0xd>;
>>>> > +            xlnx,allow-dcache-wr = <0x1>;
>>>> > +            xlnx,allow-icache-wr = <0x1>;
>>>> > +            xlnx,area-optimized = <0x0>;
>>>> > +            xlnx,avoid-primitives = <0x0>;
>>>> > +            xlnx,branch-target-cache-size = <0x0>;
>>>> > +            xlnx,cache-byte-size = <0x2000>;
>>>> > +            xlnx,d-axi = <0x1>;
>>>> > +            xlnx,d-lmb = <0x1>;
>>>> > +            xlnx,d-plb = <0x0>;
>>>> > +            xlnx,data-size = <0x20>;
>>>> > +            xlnx,dcache-addr-tag = <0xd>;
>>>> > +            xlnx,dcache-always-used = <0x1>;
>>>> > +            xlnx,dcache-byte-size = <0x2000>;
>>>> > +            xlnx,dcache-data-width = <0x0>;
>>>> > +            xlnx,dcache-force-tag-lutram = <0x0>;
>>>> > +            xlnx,dcache-interface = <0x0>;
>>>> > +            xlnx,dcache-line-len = <0x4>;
>>>> > +            xlnx,dcache-use-fsl = <0x0>;
>>>> > +            xlnx,dcache-use-writeback = <0x0>;
>>>> > +            xlnx,dcache-victims = <0x0>;
>>>> > +            xlnx,debug-enabled = <0x1>;
>>>> > +            xlnx,div-zero-exception = <0x0>;
>>>> > +            xlnx,dynamic-bus-sizing = <0x1>;
>>>> > +            xlnx,ecc-use-ce-exception = <0x0>;
>>>> > +            xlnx,edge-is-positive = <0x1>;
>>>> > +            xlnx,endianness = <0x1>;
>>>> > +            xlnx,family = "spartan6";
>>>> > +            xlnx,fault-tolerant = <0x0>;
>>>> > +            xlnx,fpu-exception = <0x0>;
>>>> > +            xlnx,freq = <0x3f940ab>;
>>>> > +            xlnx,fsl-data-size = <0x20>;
>>>> > +            xlnx,fsl-exception = <0x0>;
>>>> > +            xlnx,fsl-links = <0x0>;
>>>> > +            xlnx,i-axi = <0x0>;
>>>> > +            xlnx,i-lmb = <0x1>;
>>>> > +            xlnx,i-plb = <0x0>;
>>>> > +            xlnx,icache-always-used = <0x1>;
>>>> > +            xlnx,icache-data-width = <0x0>;
>>>> > +            xlnx,icache-force-tag-lutram = <0x0>;
>>>> > +            xlnx,icache-interface = <0x0>;
>>>> > +            xlnx,icache-line-len = <0x4>;
>>>> > +            xlnx,icache-streams = <0x0>;
>>>> > +            xlnx,icache-use-fsl = <0x0>;
>>>> > +            xlnx,icache-victims = <0x0>;
>>>> > +            xlnx,ill-opcode-exception = <0x0>;
>>>> > +            xlnx,instance = "microblaze_0";
>>>> > +            xlnx,interconnect = <0x2>;
>>>> > +            xlnx,interconnect-m-axi-dc-aw-register = <0x0>;
>>>> > +            xlnx,interconnect-m-axi-dc-read-issuing = <0x2>;
>>>> > +            xlnx,interconnect-m-axi-dc-w-register = <0x0>;
>>>> > +            xlnx,interconnect-m-axi-dc-write-issuing = <0x20>;
>>>> > +            xlnx,interconnect-m-axi-dp-read-issuing = <0x1>;
>>>> > +            xlnx,interconnect-m-axi-dp-write-issuing = <0x1>;
>>>> > +            xlnx,interconnect-m-axi-ic-read-issuing = <0x2>;
>>>> > +            xlnx,interconnect-m-axi-ip-read-issuing = <0x1>;
>>>> > +            xlnx,interrupt-is-edge = <0x0>;
>>>> > +            xlnx,lockstep-slave = <0x0>;
>>>> > +            xlnx,mmu-dtlb-size = <0x1>;
>>>> > +            xlnx,mmu-itlb-size = <0x1>;
>>>> > +            xlnx,mmu-privileged-instr = <0x0>;
>>>> > +            xlnx,mmu-tlb-access = <0x3>;
>>>> > +            xlnx,mmu-zones = <0x2>;
>>>> > +            xlnx,number-of-pc-brk = <0x1>;
>>>> > +            xlnx,number-of-rd-addr-brk = <0x0>;
>>>> > +            xlnx,number-of-wr-addr-brk = <0x0>;
>>>> > +            xlnx,opcode-0x0-illegal = <0x0>;
>>>> > +            xlnx,optimization = <0x0>;
>>>> > +            xlnx,pvr = <0x0>;
>>>> > +            xlnx,pvr-user1 = <0x0>;
>>>> > +            xlnx,pvr-user2 = <0x0>;
>>>> > +            xlnx,reset-msr = <0x0>;
>>>> > +            xlnx,sco = <0x0>;
>>>> > +            xlnx,stream-interconnect = <0x0>;
>>>> > +            xlnx,unaligned-exceptions = <0x0>;
>>>> > +            xlnx,use-barrel = <0x1>;
>>>> > +            xlnx,use-branch-target-cache = <0x0>;
>>>> > +            xlnx,use-dcache = <0x1>;
>>>> > +            xlnx,use-div = <0x0>;
>>>> > +            xlnx,use-ext-brk = <0x1>;
>>>> > +            xlnx,use-ext-nm-brk = <0x1>;
>>>> > +            xlnx,use-extended-fsl-instr = <0x0>;
>>>> > +            xlnx,use-fpu = <0x0>;
>>>> > +            xlnx,use-hw-mul = <0x1>;
>>>> > +            xlnx,use-icache = <0x1>;
>>>> > +            xlnx,use-interrupt = <0x1>;
>>>> > +            xlnx,use-mmu = <0x3>;
>>>> > +            xlnx,use-msr-instr = <0x1>;
>>>> > +            xlnx,use-pcmp-instr = <0x0>;
>>>> > +            xlnx,use-stack-protection = <0x0>;
>>>> > +        } ;
>>>> > +    } ;
>>>> > +    axi4lite_0: axi at 0 {
>>>> > +        #address-cells = <1>;
>>>> > +        #size-cells = <1>;
>>>> > +        compatible = "xlnx,axi-interconnect-1.03.a", "simple-bus";
>>>> > +        ranges ;
>>>> > +        Ethernet_MAC: ethernet at 40e00000 {
>>>> > +            compatible = "xlnx,axi-ethernetlite-1.00.a",
>>>> > "xlnx,xps-ethernetlite-1.00.a";
>>>> > +            device_type = "network";
>>>> > +            interrupt-parent = <&microblaze_0_intc>;
>>>> > +            interrupts = < 2 0 >;
>>>> > +            local-mac-address = [ 00 0a 35 aa de 00 ];
>>>> > +//            phy-handle = <&phy0>;
>>>> > +            reg = < 0x40e00000 0x10000 >;
>>>> > +            xlnx,duplex = <0x1>;
>>>> > +            xlnx,family = "spartan6";
>>>> > +            xlnx,include-global-buffers = <0x0>;
>>>> > +            xlnx,include-internal-loopback = <0x0>;
>>>> > +            xlnx,include-mdio = <0x1>;
>>>> > +            xlnx,include-phy-constraints = <0x1>;
>>>> > +            xlnx,interconnect-s-axi-read-acceptance = <0x1>;
>>>> > +            xlnx,interconnect-s-axi-write-acceptance = <0x1>;
>>>> > +            xlnx,rx-ping-pong = <0x0>;
>>>> > +            xlnx,s-axi-aclk-period-ps = <0x3a98>;
>>>> > +            xlnx,s-axi-id-width = <0x1>;
>>>> > +            xlnx,s-axi-supports-narrow-burst = <0x0>;
>>>> > +            xlnx,tx-ping-pong = <0x0>;
>>>> > +/*
>>>> > +            mdio {
>>>> > +                #address-cells = <1>;
>>>> > +                #size-cells = <0>;
>>>> > +                phy0: phy at 7 {
>>>> > +                    compatible = "marvell,88e1111";
>>>> > +                    device_type = "ethernet-phy";
>>>> > +                    reg = <7>;
>>>> > +                } ;
>>>> > +            } ;
>>>> > +*/
>>>> > +        } ;
>>>> > +        SPI_FLASH: spi at 40a00000 {
>>>> > +            compatible = "xlnx,axi-spi-1.01.a",
>>>> "xlnx,xps-spi-2.00.a";
>>>> > +            interrupt-parent = <&microblaze_0_intc>;
>>>> > +            interrupts = < 1 2 >;
>>>> > +            reg = < 0x40a00000 0x10000 >;
>>>> > +            xlnx,family = "spartan6";
>>>> > +            xlnx,fifo-exist = <0x1>;
>>>> > +            xlnx,num-ss-bits = <0x1>;
>>>> > +            xlnx,num-transfer-bits = <0x8>;
>>>> > +            xlnx,sck-ratio = <0x4>;
>>>> > +        } ;
>>>> > +        USB_Uart: serial at 40600000 {
>>>> > +            clock-frequency = <66666667>;
>>>> > +            compatible = "xlnx,axi-uartlite-1.02.a",
>>>> > "xlnx,xps-uartlite-1.00.a";
>>>> > +            current-speed = <115200>;
>>>> > +            device_type = "serial";
>>>> > +            interrupt-parent = <&microblaze_0_intc>;
>>>> > +            interrupts = < 3 0 >;
>>>> > +            port-number = <0>;
>>>> > +            reg = < 0x40600000 0x10000 >;
>>>> > +            xlnx,baudrate = <0x1c200>;
>>>> > +            xlnx,data-bits = <0x8>;
>>>> > +            xlnx,family = "spartan6";
>>>> > +            xlnx,odd-parity = <0x1>;
>>>> > +            xlnx,s-axi-aclk-freq-hz = <0x3f940ab>;
>>>> > +            xlnx,use-parity = <0x0>;
>>>> > +        } ;
>>>> > +        microblaze_0_intc: interrupt-controller at 41200000 {
>>>> > +            #interrupt-cells = <0x2>;
>>>> > +            compatible = "xlnx,axi-intc-1.01.a",
>>>> "xlnx,xps-intc-1.00.a";
>>>> > +            interrupt-controller ;
>>>> > +            reg = < 0x41200000 0x10000 >;
>>>> > +            xlnx,kind-of-intr = <0xc>;
>>>> > +            xlnx,num-intr-inputs = <0x4>;
>>>> > +        } ;
>>>> > +        system_timer: timer at 41c00000 {
>>>> > +            clock-frequency = <66666667>;
>>>> > +            compatible = "xlnx,axi-timer-1.02.a",
>>>> "xlnx,xps-timer-1.00.a";
>>>> > +            interrupt-parent = <&microblaze_0_intc>;
>>>> > +            interrupts = < 0 2 >;
>>>> > +            reg = < 0x41c00000 0x10000 >;
>>>> > +            xlnx,count-width = <0x20>;
>>>> > +            xlnx,family = "spartan6";
>>>> > +            xlnx,gen0-assert = <0x1>;
>>>> > +            xlnx,gen1-assert = <0x1>;
>>>> > +            xlnx,one-timer-only = <0x0>;
>>>> > +            xlnx,trig0-assert = <0x1>;
>>>> > +            xlnx,trig1-assert = <0x1>;
>>>> > +        } ;
>>>> > +    } ;
>>>> > +} ;
>>>> > diff --git a/board/relinux/avnet_LX9MicroBoard/lx9_mmu_defconfig
>>>> > b/board/relinux/avnet_LX9MicroBoard/lx9_mmu_defconfig
>>>> > new file mode 100644
>>>> > index 0000000..5d01ca0
>>>> > --- /dev/null
>>>> > +++ b/board/relinux/avnet_LX9MicroBoard/lx9_mmu_defconfig
>>>> > @@ -0,0 +1,68 @@
>>>> > +CONFIG_EXPERIMENTAL=y
>>>> > +CONFIG_SYSVIPC=y
>>>> > +CONFIG_IKCONFIG=y
>>>> > +CONFIG_IKCONFIG_PROC=y
>>>> > +CONFIG_BLK_DEV_INITRD=y
>>>> > +CONFIG_INITRAMFS_SOURCE="rootfs.cpio"
>>>> > +CONFIG_INITRAMFS_COMPRESSION_GZIP=y
>>>> > +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
>>>> > +CONFIG_EXPERT=y
>>>> > +CONFIG_KALLSYMS_ALL=y
>>>> > +CONFIG_KALLSYMS_EXTRA_PASS=y
>>>> > +# CONFIG_HOTPLUG is not set
>>>> > +# CONFIG_BASE_FULL is not set
>>>> > +# CONFIG_FUTEX is not set
>>>> > +# CONFIG_EPOLL is not set
>>>> > +# CONFIG_SIGNALFD is not set
>>>> > +# CONFIG_SHMEM is not set
>>>> > +CONFIG_SLAB=y
>>>> > +CONFIG_MODULES=y
>>>> > +CONFIG_MODULE_UNLOAD=y
>>>> > +# CONFIG_BLK_DEV_BSG is not set
>>>> > +# CONFIG_OPT_LIB_ASM is not set
>>>> > +CONFIG_KERNEL_BASE_ADDR=0x80000000
>>>> > +CONFIG_XILINX_MICROBLAZE0_FAMILY="spartan6"
>>>> > +CONFIG_XILINX_MICROBLAZE0_USE_MSR_INSTR=1
>>>> > +# CONFIG_XILINX_MICROBLAZE0_USE_PCMP_INSTR is not set
>>>> > +CONFIG_XILINX_MICROBLAZE0_USE_BARREL=1
>>>> > +CONFIG_XILINX_MICROBLAZE0_USE_HW_MUL=1
>>>> > +CONFIG_XILINX_MICROBLAZE0_HW_VER="8.20.a"
>>>> > +CONFIG_HZ_100=y
>>>> > +CONFIG_MMU=y
>>>> > +CONFIG_CMDLINE_BOOL=y
>>>> > +CONFIG_CMDLINE_FORCE=y
>>>> > +CONFIG_NET=y
>>>> > +CONFIG_PACKET=y
>>>> > +CONFIG_UNIX=y
>>>> > +CONFIG_INET=y
>>>> > +# CONFIG_INET_LRO is not set
>>>> > +# CONFIG_IPV6 is not set
>>>> > +CONFIG_PROC_DEVICETREE=y
>>>> > +CONFIG_BLK_DEV_RAM=y
>>>> > +CONFIG_BLK_DEV_RAM_SIZE=8192
>>>> > +CONFIG_NETDEVICES=y
>>>> > +CONFIG_NET_ETHERNET=y
>>>> > +CONFIG_XILINX_EMACLITE=y
>>>> > +# CONFIG_INPUT is not set
>>>> > +# CONFIG_SERIO is not set
>>>> > +# CONFIG_VT is not set
>>>> > +CONFIG_SERIAL_UARTLITE=y
>>>> > +CONFIG_SERIAL_UARTLITE_CONSOLE=y
>>>> > +# CONFIG_HW_RANDOM is not set
>>>> > +# CONFIG_HWMON is not set
>>>> > +# CONFIG_USB_SUPPORT is not set
>>>> > +CONFIG_EXT2_FS=y
>>>> > +# CONFIG_DNOTIFY is not set
>>>> > +CONFIG_NFS_FS=y
>>>> > +CONFIG_NFS_V3=y
>>>> > +CONFIG_CIFS=y
>>>> > +CONFIG_CIFS_STATS=y
>>>> > +CONFIG_CIFS_STATS2=y
>>>> > +CONFIG_PARTITION_ADVANCED=y
>>>> > +CONFIG_DEBUG_KERNEL=y
>>>> > +CONFIG_DETECT_HUNG_TASK=y
>>>> > +CONFIG_DEBUG_SLAB=y
>>>> > +CONFIG_DEBUG_SPINLOCK=y
>>>> > +CONFIG_DEBUG_INFO=y
>>>> > +CONFIG_EARLY_PRINTK=y
>>>> > +# CONFIG_CRYPTO_ANSI_CPRNG is not set
>>>> > diff --git a/configs/spartan6lx9_mb_defconfig
>>>> > b/configs/spartan6lx9_mb_defconfig
>>>> > new file mode 100644
>>>> > index 0000000..0329bb4
>>>> > --- /dev/null
>>>> > +++ b/configs/spartan6lx9_mb_defconfig
>>>> > @@ -0,0 +1,17 @@
>>>> > +BR2_microblaze=y
>>>> > +BR2_TOOLCHAIN_EXTERNAL=y
>>>> > +BR2_TOOLCHAIN_EXTERNAL_PATH="/opt/microblazeel-unknown-linux-gnu/"
>>>> > +BR2_TOOLCHAIN_EXTERNAL_CUSTOM_PREFIX="microblazeel-unknown-linux-gnu"
>>>> > +BR2_TOOLCHAIN_EXTERNAL_CUSTOM_GLIBC=y
>>>> > +BR2_TOOLCHAIN_EXTERNAL_CXX=y
>>>> > +BR2_TARGET_GENERIC_HOSTNAME="Microblaze Buildroot"
>>>> > +BR2_TARGET_GENERIC_ISSUE="Welcome to Microblaze Buildroot"
>>>> > +BR2_TARGET_GENERIC_GETTY_PORT="ttyUL0"
>>>> > +# BR2_TARGET_ROOTFS_TAR is not set
>>>> > +BR2_TARGET_ROOTFS_INITRAMFS=y
>>>> > +BR2_LINUX_KERNEL=y
>>>> > +BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
>>>> >
>>>> +BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="$(TOPDIR)/board/relinux/avnet_LX9MicroBoard/lx9_mmu_defconfig"
>>>> >
>>>> +BR2_LINUX_KERNEL_DTS_FILE="$(TOPDIR)/board/relinux/avnet_LX9MicroBoard/lx9_mmu.dts"
>>>> > +BR2_LINUX_KERNEL_IMAGE_TARGET_CUSTOM=y
>>>> > +BR2_LINUX_KERNEL_IMAGE_TARGET_NAME="simpleImage.lx9_mmu"
>>>> > diff --git a/linux/Config.in b/linux/Config.in
>>>> > index 86dc32a..138feb3 100644
>>>> > --- a/linux/Config.in
>>>> > +++ b/linux/Config.in
>>>> > @@ -120,6 +120,14 @@ config BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE
>>>> >      help
>>>> >        Path to the kernel configuration file
>>>> >
>>>> > +config BR2_LINUX_KERNEL_DTS_FILE
>>>> > +    string "Device Tree dts file location"
>>>> > +    depends on BR2_microblaze
>>>> > +    help
>>>> > +      Path from where the dts file has to be copied
>>>> > +      The final "custom target" name depends on the
>>>> > +      dts file name:
>>>> > +          <name>.dts --> simpleImage.<name>
>>>> >  #
>>>> >  # Binary format
>>>> >  #
>>>> > diff --git a/linux/linux.mk b/linux/linux.mk
>>>> > index ae236d4..4a24f18 100644
>>>> > --- a/linux/linux.mk
>>>> > +++ b/linux/linux.mk
>>>> > @@ -117,6 +117,18 @@ endef
>>>> >
>>>> >  LINUX_POST_PATCH_HOOKS += LINUX_APPLY_PATCHES
>>>> >
>>>> > +ifeq ($(KERNEL_ARCH),microblaze)
>>>> > +# on microblaze, we always want mkimage
>>>> > +LINUX_DEPENDENCIES+=host-uboot-tools
>>>> > +
>>>> > +define LINUX_COPY_DTS
>>>> > +    if test -f "$(BR2_LINUX_KERNEL_DTS_FILE)" ; then \
>>>> > +        cp $(BR2_LINUX_KERNEL_DTS_FILE)
>>>> $(@D)/arch/microblaze/boot/dts ; \
>>>> > +    else \
>>>> > +        echo "Cannot copy dts file!" ; \
>>>> > +    fi
>>>> > +endef
>>>> > +endif
>>>> >
>>>> >  ifeq ($(BR2_LINUX_KERNEL_USE_DEFCONFIG),y)
>>>> >  KERNEL_SOURCE_CONFIG = $(KERNEL_ARCH_PATH)/configs/$(call
>>>> > qstrip,$(BR2_LINUX_KERNEL_DEFCONFIG))_defconfig
>>>> > diff --git a/target/Config.in.arch b/target/Config.in.arch
>>>> > index 417441d..3a75585 100644
>>>> > --- a/target/Config.in.arch
>>>> > +++ b/target/Config.in.arch
>>>> > @@ -21,6 +21,8 @@ config BR2_i386
>>>> >  config BR2_m68k
>>>> >      bool "m68k"
>>>> >      depends on BROKEN # ice in uclibc / inet_ntoa_r
>>>> > +config BR2_microblaze
>>>> > +    bool "microblaze"
>>>> >  config BR2_mips
>>>> >      bool "mips"
>>>> >  config BR2_mipsel
>>>> > @@ -508,6 +510,7 @@ config BR2_ARCH
>>>> >      default "i686"        if BR2_x86_athlon
>>>> >      default "i686"        if BR2_x86_athlon_4
>>>> >      default "m68k"        if BR2_m68k
>>>> > +    default "microblaze"    if BR2_microblaze
>>>> >      default "mips"        if BR2_mips
>>>> >      default "mipsel"    if BR2_mipsel
>>>> >      default "powerpc"    if BR2_powerpc
>>>> > @@ -533,7 +536,7 @@ config BR2_ARCH
>>>> >
>>>> >  config BR2_ENDIAN
>>>> >      string
>>>> > -    default "LITTLE" if BR2_arm || BR2_bfin || BR2_i386 ||
>>>> BR2_mipsel || \
>>>> > +    default "LITTLE" if BR2_arm || BR2_bfin || BR2_i386 ||
>>>> BR2_mipsel ||
>>>> > BR2_microblaze || \
>>>> >                  BR2_sh3 || BR2_sh4 || BR2_sh4a || BR2_x86_64 ||
>>>> BR2_sh64
>>>> >      default "BIG"    if BR2_armeb || BR2_avr32 || BR2_m68k ||
>>>> BR2_mips || \
>>>> >                  BR2_powerpc || BR2_sh2 || BR2_sh2a || \
>>>> > @@ -598,6 +601,7 @@ config BR2_GCC_TARGET_TUNE
>>>> >      default 68030        if BR2_m68k_68030
>>>> >      default 68040        if BR2_m68k_68040
>>>> >      default 68060        if BR2_m68k_68060
>>>> > +    default microblaze    if BR2_microblaze
>>>> >      default mips1        if BR2_mips_1
>>>> >      default mips2        if BR2_mips_2
>>>> >      default mips3        if BR2_mips_3
>>>> > --
>>>> > 1.7.9
>>>> >
>>>> >
>>>> >
>>>> > 2012/2/11 <buildroot-request at busybox.net>
>>>> >>
>>>> >>
>>>> >> On Saturday 11 February 2012 05:58:37 Spenser Gilliland wrote:
>>>> >> > I'm using this Microblaze patch for my project.  Will it be part of
>>>> >> > the official release that is coming up soon?
>>>> >>
>>>> >>  I'm afraid it got lost between the cracks.  Could you repost it?
>>>> >>
>>>> >>  Regards,
>>>> >>  Arnout
>>>> >
>>>> >
>>>> >
>>>> > _______________________________________________
>>>> > buildroot mailing list
>>>> > buildroot at busybox.net
>>>> > http://lists.busybox.net/mailman/listinfo/buildroot
>>>>
>>>>
>>>>
>>>> --
>>>> Spenser Gilliland
>>>> Computer Engineer
>>>> Illinois Institute of Technology
>>>>
>>>
>>>
>>>
>>> --
>>> Álvaro Gámez Machado
>>>
>>>
>>
>>
>> --
>> Álvaro Gámez Machado
>>
>>
>> _______________________________________________
>> buildroot mailing list
>> buildroot at busybox.net
>> http://lists.busybox.net/mailman/listinfo/buildroot
>>
>


-- 
Álvaro Gámez Machado
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.busybox.net/pipermail/buildroot/attachments/20120213/b05bc8ff/attachment-0001.html>


More information about the buildroot mailing list